Tony Bourke Server Load Balancing phần 7 ppsx

... 192.168.0.200 Add the real servers with the add command: lb-l(config-owner-content [tony- vip-l])# add service ws-1 lb-l(config-owner-content [tony- vip-l])# add service ws-2 lb-1(config-owner-content [tony- vip-1])# ... must be an owner. Create the owner " ;tony& quot; using the owner command: lb-1(config)# owner tony Create owner < ;tony& gt;, [y/n]:y lb-1(config-owner [tony] ) 120...

Ngày tải lên: 13/08/2014, 21:21

... Real Server Server Server Real Real Real Server Server Server Figure 2-3. An active-active redundancy scenario Real Real Real Server Server Server Real Real Real Server Server Server Figure 2-4. ... This process also adds 20 Chapter 2: Concepts of Server Load Balancing Real Real Real Real Real Real Server Server Server Server Server Server Figure 2-5. An active-act...

Ngày tải lên: 13/08/2014, 21:21

... switch-based load bal- ancer or the server- based load balancer. Each has its general advantages and drawbacks, but these greatly depend on how the vendor has implemented the technology. Server- Based Load ... and server- based load balancers. With server- based load balancers, this degradation is very linear as you add func- tions. The more the processor has to do, the lower th...

Ngày tải lên: 13/08/2014, 21:21

... necessarily the subnet speci- fied). Web Servers Since I am talking about implementing Server Load Balancing, I need servers to load balance. I call these web servers, since web serving is the most ... 64 Chapter 7: NAT-Based SLB Network Architecture Web Server Web Server (ws-1) (ws-2) 192.168.0.100 192.168.0.101 Web Server (ws-3) 192.168.0.102 Web Server (ws-4) 192.168.0.103...

Ngày tải lên: 13/08/2014, 21:21

... /info/slb/ real 1: >> Real server 1 # /info/slb/real 1 1: ws-1, 08:00:20:d9:63:2c, vlan 1, port 1, health 3, up >> Server Load Balancing Information# This shows that real server 1, named ws-1, ... SLB port 1# server Current server processing: disabled Enter new server processing [d/e] : e Real Servers Under the /cfg/slb/ directory, select rea . You will be asked wh...

Ngày tải lên: 13/08/2014, 21:21

... server or group name - Set real server group name realthr - Set real server failure threshold add - Add real server rem - Remove real server del - Delete real server group cur - Display current ... select 1: >> Layer 4# real Enter real server number: (1-255) 1 [Real server 1 Menu] rip - Set IP addr of real server name - Set server name weight - Set server weight ma...

Ngày tải lên: 13/08/2014, 21:21

... 37 164 976 02 174 40391116615335 573 740343 478 5228304834580534 978 9986 379 25 677 39951119441223 9580361864968528683258995869053052354425464551516081013231328282382286208 474 10 879 4 63 674 92 373 4368989568049501 474 9 276 474 3412 177 726429520954 071 733644523613364698108210 6220323189989188 575 76903449891522965999309640222221113350 677 7 17 ... 37 164 976 02 174 40391116615335 573...

Ngày tải lên: 13/08/2014, 21:21

... source web server. This would be part of an Apache configuration for a non-DSR-configured web server: <VirtualHost 198.168.0.100> ServerAdmin tony@ vegan.net DocumentRoot /www/docs/ ServerName ... Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU: 1500 Metric:1 RX packets:6 079 071 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 177 762 errors:0 dropped:0 overruns:12 carrier:...

Ngày tải lên: 13/08/2014, 21:21

... 8 load- balancing, 22 aliases, IP addresses (Solaris), 152 Alteon, 75 CLI, 76 -77 commands, 141-142 configuration, 75 , 78 encrypted access, 83-84 flat-based SLB, 84-90 groups, flat-based SLB, 87- 88 IP ... addresses, 78 load- balancing switches, 31 NAT-based SLB, 90-95 network setup, 78 -79 passwords, 82 redundancy, NAT-based SLB, 95-98 security, 81-84 switches, Layer 2 -7, 7...

Ngày tải lên: 13/08/2014, 21:21