Intro to Marine Engineering 2E Episode 13 pps

... loss-flow characteristic, 113, 114 Heat, 353 Heat detector, 233 Heat exchangers maintenance, 139 operation, 139 plate type, 139 shell and tube type, 138 , 139 Heat treatment, 331, ... processes, 331 Acidity, 152 Actuator, 310 Admiralty coefficient, 358 Aerobic bacteria, 147 Air compressors, 134 -137 automatic valves, 137 water jacket safety valve, 135...

Ngày tải lên: 13/08/2014, 16:22

... Welin Davit & Engineering Co. Ltd Weser AG Wilson Elsan Marine International Ltd Worthington-Simpson Ltd Young and Cunningham Ltd Introduction to Marine Engineering . Engine ... marine engineering 2nd ed. 1. Marine engineering I. Title 623.87 Library of Congress Cataloguing in Publication Data Taylor, D. A. Introduction to marine engineering/...

Ngày tải lên: 13/08/2014, 16:22

... use, e.g. the steam -to- steam generator, the double evaporation boiler and various exhaust gas boiler arrangements. The steam -to- steam generator Steam -to- steam generators produce low-pressure ... the de-aerator. The de-aerator feedwater is very close to the steam temperature at the same pressure and will, if subjected to any pressure drop, 'flash-off in...

Ngày tải lên: 13/08/2014, 16:22

... manually operated to supply water to the sprayers (Figure 13. 10(b)). The system is pressurised by compressed air with a salt water pump arranged to cut in automatically if the ... fresh water to reduce corrosion effects. Valve and gasket Spray deflector Figure 13. 9 Sprinkler head 244 Fire fighting and safety cylinders of gas to be released into the...

Ngày tải lên: 13/08/2014, 16:22

... may have to be taken during the various tours. Between tours of inspection the Duty Engineer will be on call and should be ready to investigate any alarms relayed to his cabin ... small amounts to increase strength and resistance to fatigue. Tungsten added at between 12 and 18%, together with up to 5% chromium, produces high speed steel. .S32 En...

Ngày tải lên: 13/08/2014, 16:22

... points in the machinery space. A separate piston cooling system is used to limit any contamination from piston cooling glands to the piston cooling system only. Sea water cooling system The ... delivered to the injector nozzle at very high pressure. When the edge of the helix at C uncovers the spill port D pressure is lost and fuel delivery to the...

Ngày tải lên: 13/08/2014, 16:22

... made up of a torque tube, membranes and adaptor plates. The torque tube fits between the turbine rotor and the gearbox pinion. The adaptor plates are spigoted and dowelled onto the ... provides steam to act on the dummy piston which is mounted on the turbine rotor (Figure 3.7). The rotor casing provides the cylinder to enable the steam pressure to crea...

Ngày tải lên: 13/08/2014, 16:22

... and could lead to fires or explosions. The compressor motor is started and the machine run up to speed. The lubricating oil pressure should be observed to build up to the correct ... according to the type of seal. Replaceable wear rings are fitted to the impeller and the casing. The motor support bracket has two large apertures to provide access...

Ngày tải lên: 13/08/2014, 16:22

... pump (see Chapter 6). To achieve a seal between the rotors, oil is injected into the compressor: to prevent this being carried into the system, the oil separator is larger and ... or rolling. Evaporators Evaporators fall into two categories: refrigerant to air and refrigerant to secondary refrigerant types. The most simple of the refrigerant to air type...

Ngày tải lên: 13/08/2014, 16:22