Industrial Control Wiring Guide 2E Episode 10 ppt

... ‘scr’ is an interference screen which should be connected to the chassis. ᭹ Never deviate from the wiring drawing since in most cases the terminals are not interchangeable. 91 8. COMPONENTS (ACTIVE) Overload ... variety of types, shapes and sizes available but there are only a couple which are in common use in control panel assembly. ᭹ Fuses are an essential part of the safety element of...

Ngày tải lên: 13/08/2014, 16:21

... for safety is powered by a low voltage supply. ᭹ The temperature control may be incorporated in the base unit and varied by a control knob. ᭹ In other irons the tip itself determines the operating ... regular intervals and normally this will be carried out by your supervisor or a member of the quality control team who will keep records. 32 4. SOLDERING AND TERMINATION Summary Soldering...

Ngày tải lên: 13/08/2014, 16:21

... material. So the full specification for a 10, 000 ohm pot with a carbon resistance track could be: 10K, 10% , log, 0.25 W, carbon. Most preset pots are linear types. 102 9. COMPONENTS (PASSIVE) 9.2.6. ... linear, lin or ln. ᭹ Logarithmic are marked log or lg. A 10, 000 ohm, 10% pot where the resistance varied logarithmically would be marked: 10KK log. The other parts of the specificatio...

Ngày tải lên: 13/08/2014, 16:21

... abbreviated to: ᭹ 1 microfarad = 10 –6 farads, shortened to ␮F. ᭹ 1 nanofarad = 10 –3 microfarads, or 10 –9 farads, shortened to nF. ᭹ 1 picofarad = 10 –3 nanofarads, or 10 –12 farads, shortened to ... by 100 0. For example: 100 0 pF = 1 nF ᭹ pF to ␮F – divide by 1,000,000. For example: 10, 000 pF = 0.01 ␮F ᭹ nF to ␮F – divide by 100 0. For example: 47 nF = 0.047 ␮F ᭹ ␮F to nF –...

Ngày tải lên: 13/08/2014, 16:21

... Components (passive) 92 9.1. Fuses 92 9.2. Resistors 96 9.3. Capacitors 103 10 Switches and lamps 108 10. 1. Switches 108 10. 2. Lamps 112 11 Earthing and screening 114 11.1. Earthing the protective ... plastic tubing (PVC conduit) even a dry piece of cloth folded several times will do. 2 Industrial Control Wiring Guide Second edition Bob Mercer OXFORD AUCKLAND BOSTON JOHA...

Ngày tải lên: 13/08/2014, 16:21

... PVC-insulated cable for switchgear and controlgear wiring. This deals with the requirements for the wires and cables used in the wiring of control panels up to 600 V /100 0 V. 1.2.3. The IEE regulations ... detailed guide to the requirements of the various classes as defined in Part 1. ᭹ BS 7452: Specification for transformers of the type used in control panels. Equivalent to IEC 989...

Ngày tải lên: 13/08/2014, 16:21

... cutting blades can be changed to suit different sizes of conductor diameters. ᭹ A ‘length of strip’ guide post can also be fitted. Operation ᭹ Place the wire between the jaws from the clamping jaw ... shield to screen the internal conductors from outside electro- magnetic interference. Screened wiring is generally only used for DC and lower frequency signals such as audio. It is often use...

Ngày tải lên: 13/08/2014, 16:21

... conductor. 38 4. SOLDERING AND TERMINATION 4.5. Crimped joints The majority of wire terminations used in control panel assembly are made with crimp connectors. The main reason for this is that they are

Ngày tải lên: 13/08/2014, 16:21

... installed and the following information is usually provided: ᭹ Wiring schedule. ᭹ Cableform template. ᭹ Run-out sheet or table. 5.1.1. Wiring schedule This gives details of the wires used in the ... then squeeze the jaws lightly to grip the insulation. ᭹ Comb out the braiding and trim down to about 10 mm long. Fold it back over the clip. ᭹ Strip the centre insulation to the required len...

Ngày tải lên: 13/08/2014, 16:21

... the wire diameter. ᭹ This table gives a guide. If one wire is thicker then this diameter determines the length of twist. Summary ᭹ Mains and other power wiring must be formed into a separate cable ... power wiring must be formed into a separate cable form from all other wires. ᭹ Power wiring must conform to the IEE wiring regulations. ᭹ There must be no strain on any wires at junctio...

Ngày tải lên: 13/08/2014, 16:21