Marine Auxiliary Machinery 7E Episode 7 pptx

... expansion. New seals are fitted by cutting and vulcanizing in position. 234 Auxiliary power Figure 7. 14 Auxiliary condensing turbine (Peter Brotherhood Ltd) 1. Pedestal end bearing ... underslung) or to a separate central auxiliary condenser or the ship's main condenser. A typical auxiliary condensing turbine is shown in Figure 7. 14. Alternatively th...

Ngày tải lên: 13/08/2014, 16:21

... Publication Data Marine Auxiliary Machinery - 7 lh rev. edn I. McGeorge, H. David 0623.8 Library of Congress Cataloguing in Publication Data McCeorge, H. D. Marine Auxiliary Machinery/ H. ... Reprinted 1 976 ,1 979 Second edition 1955 Sixth edition 1983 Third edition 1963 Reprinted 19 87 Fourth edition 1968 Seventh edition 1995 Reprinted 1 971 ,1 973 Paperback...

Ngày tải lên: 13/08/2014, 16:21

... .R. (1 972 ) Titanium in marine engineering, Trans I Mar E, 84, paper 16. Conde, ]. F. G. (1985) New materials for the marine and offshore industry, Trans I Mar E, 97, paper ... stage compressor with intercooling (courtesy Ham worthy Engineering Ltd) Machinery service systems and equipment 47 require regular checking and possibly daily draining. A comp...

Ngày tải lên: 13/08/2014, 16:21

... lavatory and urinal emptyings, including flushing water, while Machinery service systems and equipment 71 Figure 2. 27 Elementary automatic combustion system System operation Control ... and together with the anticipation of the ratification of Annexe IV of the 1 973 IMCO Conference on Marine Pollution was probably more responsible for the development...

Ngày tải lên: 13/08/2014, 16:21

... emergency such as fire. Wire operated valves (Figure 4. 17) are commonly fitted, with wire pull levers located externally to the machinery space. The type shown is a Howden Instanter valve. ... 4. 27) provide extra protection for engines and gearboxes where iron or steel wear particles are likely to be present. Further reading Milton, J. H. and Leach, R. M (1...

Ngày tải lên: 13/08/2014, 16:21

... adaptation to a wide range of duties. Further reading Pearsall, IS. (1 973 ) The supercavitating pump, Proc I Mech E, 1 87, 54, 649-65, Pumps and pumping 151 must be placed below the ... contain large quantities of silt and sand Tanker and gas carrier cargo pumps and systems 177 Centrifugal cargo pumps with a double entry impeller (Figure 6,1) have replac...

Ngày tải lên: 13/08/2014, 16:21

... the deck. Auxiliary power 2 27 Figure 7. 9 Sleeve-metered fuel injection pump (Caterpillar Tractor Co.) 1. Reverse flow check valve 6. Retainer 11. Lifter 2. Chamber 7. Plunger ... (Svanehoj, Denmark). 222 Auxiliary power Figure 7. 5 Closed circuit cooling system Operation The operation of helix type pumps is shown diagrammatically in Figure 7. 6. Wit...

Ngày tải lên: 13/08/2014, 16:21

... shaft unloaidng pump cover 17. Valve rod 29. Regulating valve for 3. Blade sealing ring 18. End cover auxiliary servomotor 4. Bearing ring 19. Pitch control auxiliary 30. Reducing valve 5. ... Reducing valve 5. Hub body servomotor assembly (auxiliary servomotor) 6. Servometer piston 20. Low pressure seal 31. Back pressure 7. Hub cylinder assembly maintaining...

Ngày tải lên: 13/08/2014, 16:21

... SOLAS 1 974 , are given below: (1) Ships must have a main and an auxiliary steering gear, arranged so that the failure of one does not render the other inoperative. An auxiliary ... gas carrier of 10 000 gt and over. Auxiliary steering gear control must be arranged in the steering gear Steering gears 313 room and where the auxiliary gear is power oper...

Ngày tải lên: 13/08/2014, 16:21