Kinematic Geometry of Surface Machinin Episode Episode 7 pot
Kinematic Geometry of Surface Machinin Episode Episode 7 pot
... +
⋅
θ
(5 .77 )
The computed values of principal radii of curvature of the generating surface
T of the form-cutting tool (see Equation 5 .77 ) were used for the development
of novel designs of the ... Francis Group, LLC
196 Kinematic Geometry of Surface Machining
Use of a single-parametric kinematic scheme of surface generation allows
a simplication. The gene...
Kinematic Geometry of Surface Machinin Episode 1 doc
... Map of the Generating Surface
of the Cutting Tool 2 97
7.1.6 Important Peculiarities of Gaussian Maps
of the Surfaces P and T 299
7. 1 .7 Spherical Indicatrix of Machinability
of a Sculptured Surface ... Machining of Surfaces of Revolution 469
11.2.1 Turning Operations 469
11.2.2 Milling Operations 474
11.2.3 Machining of Cylinder Surfaces 475
11.2.4 Reinforcement...
Kinematic Geometry of Surface Machinin Episode 2 pdf
... The existence of open and closed sides of a surface P eliminates the
© 2008 by Taylor & Francis Group, LLC
28 Kinematic Geometry of Surface Machining
motion of the work and of the cutting ... LLC
30 Kinematic Geometry of Surface Machining
Implementation of the principle of inversion has proven convenient for the
investigation of multiparametric surface...
Kinematic Geometry of Surface Machinin Episode 3 pptx
... parameters
of geometry of the surface P, the kinematic schemes of surface generation
specify the generating surface of the cutting tool, as well as the principal part
of the kinematic structure of ... Francis Group, LLC
46 Kinematic Geometry of Surface Machining
nonagile kinematics of surface generation can be considered as a particular
(degenerated) case...
Kinematic Geometry of Surface Machinin Episode Episode 5 ppsx
... LLC
110 Kinematic Geometry of Surface Machining
4.4.2 Indicatrix of Conformity of the Surfaces P and T
Introduced in this section is a quantitative measure of the rate of conformity
of two surfaces. ... the local -surface contact of surfaces of the rst kind
is identical to the true -surface contact of the surfaces.
2. Consider line kind of contact of the surfa...
Kinematic Geometry of Surface Machinin Episode Episode 6 pptx
... LLC
184 Kinematic Geometry of Surface Machining
of the parameter of motion w. The theory of surface generation also deals with
surfaces for which the enveloping surface is congruent to the moving surface.
5.2.1.3 ... Filed February 17, 19 87.
© 2008 by Taylor & Francis Group, LLC
162 Kinematic Geometry of Surface Machining
computation of the actual rate...
Kinematic Geometry of Surface Machinin Episode Episode 8 pdf
... be considered as a line
of intersection of the three surfaces, say of the generating surface T of the
cutting tool, of the rake surface
R
s
, and of the clearance surface
C
s
. This
requirement ... cutting edge of a precision form-cutting tool can be considered as a line
of intersection of three surfaces: of the generating surface T of the cutting
tool, of...
Kinematic Geometry of Surface Machinin Episode Episode 9 doc
... representation of the tool-in-use system.
6.3.3 Reference Planes
Investigation of the impact of kinematics of a machining operation on actual
(kinematical) values of geometry of the active part of a cutting ... required.
7. 1.2 Gaussian Maps of a Sculptured Surface P and of the Generating
Surface T of the Cutting Tool
Gauss introduced the notion of mapping of...
Kinematic Geometry of Surface Machinin Episode Episode 10 potx
... contacting surfaces, consider the contact of
a concave portion of the sculptured surfaces P and of a convex portion of the
generating surface T of a form-cutting tool (Figure 7. 17a). In Figure 7. 17, ... radii of normal
curvature of the surfaces, the normal cross-sections of all possible kinds of
contact of the surfaces P and T have been analyzed (Table 7. 1).
TA...
Kinematic Geometry of Surface Machinin Episode Episode 11 pptx
... Co
mputer-Aided Design, 37 (7) , 76 7 77 8, 2005.
[11] Radzevich, S.P., A Generalized Analytical Form of the Conditions of Proper Part
Surface Generation. Part 1. In Improvement of Efciency of Metal Cutting, ... LLC
348 Kinematic Geometry of Surface Machining
The surface
r
R
(see Equation 7. 72) is depicted in Figure 7. 35. It is evident
that the surfaces P and
R...
Từ khóa: