Kinematic Geometry of Surface Machinin Episode Episode 5 ppsx
Kinematic Geometry of Surface Machinin Episode Episode 5 ppsx
... analytical descrip-
tion of the geometry of contact of two surfaces for the needs of the theory of
surfaces generation.
4 .5. 3.1 On a Possibility of Implementation of Two of Plücker’s Conoids
At ... LLC
110 Kinematic Geometry of Surface Machining
4.4.2 Indicatrix of Conformity of the Surfaces P and T
Introduced in this section is a quantitative measure of the rate...
Kinematic Geometry of Surface Machinin Episode 1 doc
... 455
10 .5. 6 Optimal Location of the Starting Point 457
References 457
11 Examples of Implementation of the Differential Geometry/
Kinematics (DG/K)-Based Method of Surface Generation 459
11.1 Machining ... 451
10 .5. 2 Representation of the Input Data 452
10 .5. 3 Optimal Workpiece Conguration 454
10 .5. 4 Optimal Design of the Form-Cutting Tool 454
10 .5. 5 Optimal...
Kinematic Geometry of Surface Machinin Episode 2 pdf
... The existence of open and closed sides of a surface P eliminates the
© 2008 by Taylor & Francis Group, LLC
28 Kinematic Geometry of Surface Machining
motion of the work and of the cutting ... LLC
30 Kinematic Geometry of Surface Machining
Implementation of the principle of inversion has proven convenient for the
investigation of multiparametric surface...
Kinematic Geometry of Surface Machinin Episode 3 pptx
... versions of
© 2008 by Taylor & Francis Group, LLC
52 Kinematic Geometry of Surface Machining
The analysis of kinematic schemes of surface generation (Figure 2.9) reveals
that the axodes of ... Francis Group, LLC
46 Kinematic Geometry of Surface Machining
nonagile kinematics of surface generation can be considered as a particular
(degenerated) case of...
Kinematic Geometry of Surface Machinin Episode Episode 6 pptx
... Francis Group, LLC
172 Kinematic Geometry of Surface Machining
Implementation of the screw surfaces
P
s( )
(Figure 5. 6 and Figure 5. 7) and
the surfaces of revolution (Figure 5. 8) allows one to ... LLC
184 Kinematic Geometry of Surface Machining
of the parameter of motion w. The theory of surface generation also deals with
surfaces for which the enveloping...
Kinematic Geometry of Surface Machinin Episode Episode 7 pot
... Francis Group, LLC
196 Kinematic Geometry of Surface Machining
Use of a single-parametric kinematic scheme of surface generation allows
a simplication. The generating surface T of the cutting tool ... premises of analysis of the geometry of contact of the surfaces P
and T. The optimal values of the parameters H and
c
can be drawn from the
desired degree...
Kinematic Geometry of Surface Machinin Episode Episode 8 pdf
... be considered as a line
of intersection of the three surfaces, say of the generating surface T of the
cutting tool, of the rake surface
R
s
, and of the clearance surface
C
s
. This
requirement ... cutting edge of a precision form-cutting tool can be considered as a line
of intersection of three surfaces: of the generating surface T of the cutting
tool, of...
Kinematic Geometry of Surface Machinin Episode Episode 9 doc
... plane of projections V (Figure 6. 25) .
6.4 On Capabilities of the Analysis of Geometry of the Active
Part of Cutting Tools
Implementation of the vectorial method for the computation of geometry of ... representation of the tool-in-use system.
6.3.3 Reference Planes
Investigation of the impact of kinematics of a machining operation on actual
(kinematical) values...
Kinematic Geometry of Surface Machinin Episode Episode 10 potx
... & Francis Group, LLC
312 Kinematic Geometry of Surface Machining
form of an involute surface that has the base circle of diameter
d
b
. When
machining the surface P, the cam is swinging ... radii of normal
curvature of the surfaces, the normal cross-sections of all possible kinds of
contact of the surfaces P and T have been analyzed (Table 7.1).
TABLE 7.1 A C...
Kinematic Geometry of Surface Machinin Episode Episode 11 pptx
... conguration of the focal sur-
faces. For the purpose of verication of accessibility of the surface P by the
© 2008 by Taylor & Francis Group, LLC
356 Kinematic Geometry of Surface Machining
matrix ...
© 2008 by Taylor & Francis Group, LLC
366 Kinematic Geometry of Surface Machining
[7] Pat. No. 11 857 49, USSR, A Method of Sculptured Surface Machi...
Từ khóa: