Cutting Tool Technology Episode 6 pps

... Controller’s tool table. Typical of such tooling, are special-purpose form tools that may be consid- ered to full this classication, 2. Semi-qualied tools – these are tools where not all of the tool ... non-rotating ‘Block tooling’ in: Figs. 1 16, 117 and 118), can automatically perform the functions of: tool identication, tool osets and cutting data up-dating on the machi...

Ngày tải lên: 13/08/2014, 05:20

... toolholding, tool changing, VII. Tool programme – the correct/specied tool and its tool osets, etc., VIII. Performance – cutting data, anticipated tool- life and economics, IX. Quality – tool ... operation, such as: tool- changing either by the tool turret’s rotation, or by manually changing tools, adjusting tool- osets (i.e. for either: tool wear compensation, or f...

Ngày tải lên: 13/08/2014, 05:20

... USA in work from: Coldwell and Quackenbush (1 962 ), plus Recht (1 964 ); Okushima et al. (1 966 ) and Tanaka et al. (1 967 ) in Japan; Fenton and Oxley (1 967 ) in the United Kingdom; and Arndt (1972) ... change time is 10 seconds, with a tool change time of 6 seconds (chip-to-chip), having a tool stor- age capacity of 50 tools (i.e. expandable). e standard tool spindle cartridg...

Ngày tải lên: 13/08/2014, 05:20

... achieved. e cutting tool problems, such as: too wide a range of tooling inventory, inappropriate tools/out-dated tooling, or not enough tools for the overall operational 1 Tooling refers ... coatings tend to have smoother and less Cutting Tool Materials  Figure 6. Classication of carbides according to use. [Courtesy of Seco Tools]. Cutting Tool Materials  Figure 14. A d...

Ngày tải lên: 13/08/2014, 05:20

... to 400/800 IT5 0 .6 0.8 1.3 2.2 3.2 4.5 IT6 0.9 1.2 1.9 3.1 4 .6 6.4 IT7 1.4 1.9 3.1 5.0 7.4 10.1 IT8 2.0 2.9 4.7 7.8 11.5 15.8 IT9 3 .6 7.5 9.4 12.4 18.3 25.2 IT10 5.7 7 .6 12.1 20.0 29.8 40.5 IT11 8 .6 11.8 ... Single-tube Systems, require a t of ISO G6/ h6, equating to a minimum play of 0.0 06 mm. is drill bush is usually manufactured from a hardened material (i.e. 60 to 62 HR C...

Ngày tải lên: 13/08/2014, 05:20

... Machinist, 43–45, Dec. 19 96. Isakov, E. Power Equations. Cutting Tool Eng’g., 66 –71, May 2001. Kennedy, B. Facing Facts [Face Milling – Automotive Parts]. Cutting Tool Eng’g., 29–37, Feb. 2002. Kennedy, ... Conf. on Industrial Tooling, Test Valley Group, 255– 266 , Sept. 2003. Heuwinkel, M. and Richter, A. Let’s Talk Radial [Approach Angles – Milling]. Cutting Tool Eng’g...

Ngày tải lên: 13/08/2014, 05:20

... Cutting Tool Eng’g., 62 68 , Mar. 2007. Henderer, T. Solid Synchronicity [Solid Tapping] .Cutting Tool Eng’g., 58 63 , Feb. 20 06. Jonah, A.K. Standard Taps for Exotic Materials. Cutting Tool Eng’g., ... Cutting Tool Eng’g., 56 62 , April 2007. Pontius, K. Low-silicon Lowdown [Tapping Si-Al Parts]. Cutting Tool Eng’g., 58 64 , May 2001. Restall, M. e Ins and Outs of...

Ngày tải lên: 13/08/2014, 05:20

... in Fig. 166 a), 3. Side -cutting angle – denoted by C s  (Fig. 166 a). In eect, there are three discrete ‘turning-cases: I, II and III,’ that may occur when utilising the tool nose cutting insert ... (Fig. 166 a and b), its resultant surface topography can be dened by three distinct insert-related factors, these are: 1. Nose radius – r = OT (i.e. illustrated in Fig. 166 b), 2. End...

Ngày tải lên: 13/08/2014, 05:20

... includes the: type of machining process; cutting con - ditions – workpiece material, cutting data, tool mate - rial, etc., together with the machine tool type and its conguration 18 . us, ... of cutting uids. [Courtesy of Cimcool]. Cutting Fluids  8.1 Historical Development of Cutting Fluids General speaking, metalworking mass production techniques can be traced back t...

Ngày tải lên: 13/08/2014, 05:20

... 8 HSK dual-contact tooling 466 HSM chucks – for turning operation 462 dynamic balancing machine application 472 machine tool design consideration 434 problem of tool balance 469 research application ... 319 specic cutting force 41 speed-increaser 489 speed analyser 300 speed ratio 204 spindle camber/tilt 166 spindle design 465 , 466 spindle imbalance 287 spindle...

Ngày tải lên: 13/08/2014, 05:20