Phoenix R/C Professional Model Flight Simulation User Manual Version 3 0 phần 4 ppsx

... mutebuttonwillturntheVariometertonevolume upanddownrespectively.  Flight Recorder Phoenix featuresapowerfulandfull‐featured flight recorderwhichletsyourecorda flight (orseriesofflights),and thensavetheseto disktosharewithother Phoenix ... thecurrentlyset simulation speed,with 100 %being the normal simulation rate.Formoreinformationon simulati...

Ngày tải lên: 12/08/2014, 22:21

... option. Youwillthenbetakentoanewwizardwhereyoucanveryeasilycreateanew,customcontrolprofileforyourradio makeand model.  Phoenix R/C Professional Model Flight Simulation User Manual Version 3. 0  Introduction Thankyouforchoosing Phoenix R/C –the professional model flight simulatorforalllevelsof ... Art‐tech 100 C("Art‐tech 100 Cadaptor"re...

Ngày tải lên: 12/08/2014, 22:21

... aroundthedefaultof 50% value. Simulation Speed Thisslidercontrolsthetotalspeedofthe simulation. Thedefault( 100 %)valueisthenormalspeedofthe simulation,  whereallmodelsaremovingatrealisticvelocities. Reducingthissliderbelow 100 %willcausethe simulation toappearinslow‐motion,makingiteasierto ... After 3 seconds(Default)–Whenanyimpactorda...

Ngày tải lên: 12/08/2014, 22:21

... Aftertake‐off–Thefailurewilloccurshortlyafteryour model leavestheground. • After 10 s–Thefailurewilloccurapprox. 10 secondsafteryour model leavestheground. • After 30 s–Thefailurewilloccurapprox. 30 secondsafteryour model leavestheground. • ... stronger thermalwillproducemoreupwardliftonmodelsflyinginsidethethermal’sdiameter.Asettingunde...

Ngày tải lên: 12/08/2014, 22:21

... The user willbeinformedthattheyhavebeenkickedfromyoursession,andwillnotbeabletojoinagainforat least 30 seconds. • Ban User ‐Available if you arethehost only, this button will permanently bantheselected user from the session.The user willbeinformedthattheyhavebeenbannedfromthesession,andwillnotbeabletojoin yoursessionagain. •...

Ngày tải lên: 12/08/2014, 22:21

... . . . . . . . . . . . . . 32 The DiskSim Simulation Environment Version 3. 0 Reference Manual John S. Bucy, Gregory R. Ganger, and Contributors January 20 03 CMU-CS- 03 - 102 School of Computer Science Carnegie ... required 2 1 .3 Limitations and Advantages of Version 3. 0 DiskSim 3. 0 builds on DiskSim 2 .0 in several ways: parts of DiskSim’s disk model have been m...

Ngày tải lên: 29/06/2014, 04:20

... States STATION ~~DOWN 0x 00 ~~UP 0x01 SAP ~~INACTIVE 0x 00 ~~ACTIVE 0x01 CONNECTION ~~ADM 0x 00 ~~CONN 0x01 ~~RESET_WAIT 0x02 ~~RESET_CHECK 0x 03 ~~SETUP 0x 04 ~~RESET 0x05 ~~D_CONN 0x06 ~~ERROR 0x07 ~~NORMAL 0x08 ~~BUSY ... symlink@ example% ls -li file link symlink 106 06 -rw-r r 2 user 0 Jan 12 00 :06 file 106 06 -rw-r r 2 user 0 Jan 12 00 :06 link 106 07 lrwxrwxrwx 1 u...

Ngày tải lên: 24/07/2014, 02:20

... Figure 3- 35 93 03 55 7 30 0 Ch 03 . qxd 3/ 24 / 04 9: 40 AM Page 99 Designing Reports Figure 3- 42 Figure 3- 43 99 03 55 7 30 0 Ch 03 . qxd 3/ 24 / 04 9: 40 AM Page 106 04 55 7 30 0 Ch 04. qxd 3/ 24 / 04 9 :36 AM Page 107 Report ... ReportDocument1.Load(“c:\Crystal.NET 20 03 \ Chapter 04\ ch4_worldsales.rpt”) CrystalReportViewer1.ReportSource = ReportDoc...

Ngày tải lên: 06/08/2014, 09:20

... correct usage of syntax. 233 07 55 7 30 0 Ch07.qxd 3/ 24 / 04 9 :38 AM Page 227 Working with .NET Data Figure 7-15 Figure 7-16 227 07 55 7 30 0 Ch07.qxd 3/ 24 / 04 9 :38 AM Page 2 13 Working with .NET Data ... window, as shown in Figure 7-19. Figure 7-19 229 07 55 7 30 0 Ch07.qxd 3/ 24 / 04 9 :38 AM Page 233 Working with .NET Data Figure 7- 23 Figure 7- 24 When y...

Ngày tải lên: 06/08/2014, 09:20

... user interface might not be completely static: When used as part of a data entry form, this control’s user interface might 118 Chapter 4 09 _57860x ch 04. qxd 10/ 4 /05 9 : 30 PM Page 118 Figure 4- 4 Clicking ... build the third type of component covered in this book: Web Parts. 1 30 Chapter 4 09 _57860x ch 04. qxd 10/ 4 /05 9 : 30 PM Page 1 30 ... design. 108 Chapter 3...

Ngày tải lên: 06/08/2014, 09:20