Liquid Process Piping Episode 13 pptx

... 8:3 thermoset piping and fittings, 7:1-7; 8:3 vents and drains, 3:29 wall thickness, 2:6-7; 3:5, 14-17; 7:4 P&IDs see Piping and instrumentation diagrams Piping components, 2:1-2, 6; 3:2-3,19 Piping ... devices, 11:5-7 for double containment piping, 8:7 for pneumatic testing, 3:30 Pressure wave, 3:5-7 Probe leak detection system, 8:8 Process control, 2:1-2, 4 Process flow dia...

Ngày tải lên: 12/08/2014, 16:20

... 1110-l-4008 5 May 1999 Engineering and Design LIQUID PROCESS PIPING 1. The purpose of this manual is to provide information for the design of liquid process piping. 2. Applicability. This manual applies ... used to operate the process Predesign surveys are recommended for the design of systems. Table 2-3 lists the typical items contained on a liquid process piping for new...

Ngày tải lên: 12/08/2014, 16:20

... the piping system affects the Piping systems that carry materials not listed in Table 3-6 should be located adjacent to directional changes of are addressed in liquid process piping designs in piping. ... a process tank via above grade piping. A pump is required because the process tank liquid elevation is 30 m (98.4 ft) above the equalization tank level. The piping layout...

Ngày tải lên: 12/08/2014, 16:20

... designing and for liquid process piping systems, the advantages and specifying thermoplastic piping systems for liquid disadvantages of each method are evaluated and the process piping pressure ... 3.35 (11.0) 3.05 (10.0) 2 .13 (7.0) 1.83 (6.0) 300 (12) 3.96 (13. 0) 3.66 (12.0) 3.2 (10.5) 2.29 (7.5) 1.98 (6.5) 350 (14) 4.11 (13. 5) 3.96 (13. 0) 3.35 (11.0) 2.44 (8.0) 2 .13 (7....

Ngày tải lên: 12/08/2014, 16:20

... to not sole-source the piping system. Schweitzer, Corrosion-Resistant Piping Systems, p. 102. 1 EM 1110-1-4008 5 May 99 10-1 Chapter 10 Valves 10-1. General For liquid piping systems, valves ... primary piping system usually only exhibits F = internal hydrostatic stress, MPa (psi) a larger temperature induced change when the process dictates, for example, when a hot liquid enter...

Ngày tải lên: 12/08/2014, 16:20

... 534.7 (140) for Y-pattern V = liquid flow, m/s (ft/s) $ = ratio of port diameter to inside pipe diameter v = specific volume of the liquid, m /N (ft /lb) 3 3 j = 133 .7 (35) for Y-pattern Stop ... : 3 where: v = specific volume of the liquid, m /N (ft /lb) V = liquid flow, m/s (ft/s) j = 210.0 (55) globe, OS&Y blocked bonnet v = specific volume of the liquid, m /N (ft /lb) = 286.4...

Ngày tải lên: 12/08/2014, 16:20

... resistivity: - natural gas propane piping; - liquid fuel piping; - oxygen piping; - underground storage tanks; - fire protection piping; - ductile iron pressurized piping under floor (slab on grade) ... CEGS 15080 is coordinated with the liquid process piping specification section and contract drawings. 11-10. Heat Tracing For the purposes of liquid process piping, heat...

Ngày tải lên: 12/08/2014, 16:20

... Type 2 60 (140) 60 (140) 20 (70) 60 (140) 60 (140) 60 (140) PVDF 138 (280) 138 (280) 138 (280) 138 (280) 138 (280) 138 (280) 138 (280) OTHER MATERIALS Butyl 66 (150) U 49 (120) U U EPDM U 149 ... (470) 243 (470) PVC Type 2 60 (140) 60 (140) 60 (140) 60 (140) PVDF 138 (280) 138 (280) 138 (280) 132 (270) 132 (270) 149 (300) 138 (280) OTHER MATERIALS Butyl 65 (150) 87 (190) 87 (190)...

Ngày tải lên: 12/08/2014, 16:20

... (140) 60 (140) 60 (140) PVDF 138 (280) 138 (280) 138 (280) 138 (280) 138 (280) 138 (280) OTHER MATERIALS Butyl 82 (180) 93 (200) 82 (180) 93 (200) 87 (190) EPDM 138 (280) 98 (210) 98 (210) 98 ... (140) 32 (90) 60 (140) U 32 (90) 26 (80) PVDF 138 (280) 138 (280) 138 (280) 127 (260) 121 (250) 26 (80) 38 (100) OTHER MATERIALS Butyl 54 (130 ) 54 (130 ) 82 (180) U 65 (150) EPDM 98 (210)...

Ngày tải lên: 12/08/2014, 16:20

... coefficient chart and assuming an From a lined piping manufacturer, (A )(* ) = 133 N/m P P for 80 mm lined piping and 67.1 N/m for 40 mm lined piping. 80 mm pipe: less than 10 m) so a gust factor ... point G supports piping section H-I-J and will prevent vertical deflection at point H; and 4) given that the piping system will be installed at 21EC, the thermal expansion of the pipi...

Ngày tải lên: 12/08/2014, 16:20