Specifications, Tolerances, and Other Technical Requirements for Weighing and Measuring Devices Episode 8 doc

... and other technical requirements by a state agency. B. Purpose. - The purpose of these technical requirements is to eliminate from use, weights and measures and weighing and measuring devices ... obtained. For 2-22 United States Department of Commerce Technology Administration National Institute of Standards and Technology SPECIFICATIONS, TOLERANCES, AND...

Ngày tải lên: 27/06/2014, 18:20

... units. 5 Specifications, Tolerances, and Other Technical Requirements for Weighing and Measuring Devices as adopted by the 91 st National Conference on Weights and Measures 2006 Editors: ... (Amended 1 985 , 1991, 1999, 2000, 2001, 2003 and 2006) G-S.1.1. Location of Marking Information for Not Built -For- Purpose, Software-Based Devices. - For n...

Ngày tải lên: 12/08/2014, 07:22

... 1.669 15 1.324 1.390 1.529 1. 688 1 .85 3 16 1.353 1.412 1.549 1.706 1 .87 1 17 1. 382 1.434 1.569 1.724 1 .88 8 18 1.412 1.456 1. 588 1.743 1.906 19 1.441 1.4 78 1.6 08 1.761 1.924 20 1.471 1.500 ... 1.647 1.7 98 1.959 22 1.529 1.544 1.667 1 .81 6 1.976 23 1.559 1.566 1. 686 1 .83 5 1.994 24 1. 588 1. 588 1.706 1 .85 3 2.012 2.176 25 1.6 18 1.610 1.725 1 .87 1 2.029 2.194 26...

Ngày tải lên: 12/08/2014, 07:22

... the automatic weighing system, and by the weights and measures authority having jurisdiction over the automatic weighing system. 2 -80 Handbook 44 - 2007 3.30. Liquid -Measuring Devices (d) ... 3 9.0 580 9.0 580 5.0 320 4 11.0 710 11.0 710 6.0 390 5 15 970 12.0 780 6.5 420 6 17 1190 7 19 1200 8 21 1400 15.0 970 9.0 580 9 23 1500 10 25 1600 18. 0 1160 10.0 650 15 2...

Ngày tải lên: 12/08/2014, 07:22

... methane, natural gas and any other hydrocarbon gas/air mix. (Amended 1 984 , 1 986 , 1 988 , and 1991) A.2. - This code does not apply to: (a) Liquid -measuring devices used for dispensing liquefied ... compute and indicate to the nearest 1 cent of money value (see Sec. 1.10., G-S.5.5.). (Amended 1 984 and 1 988 ) 1 Title amended 1 986 . 3-31 3.32. LPG and Anhy...

Ngày tải lên: 12/08/2014, 07:22

... 0.91 0 .89 0 .87 0 .85 0 .83 0 .81 0.79 0.77 0.75 0.73 0.71 0.69 0.67 0.65 0.63 0.61 0.59 100 .85 98. 82 96.79 94.76 92.73 90.70 88 .66 86 .63 84 .60 82 .57 80 .54 78. 51 76. 48 74.45 ... 102. 58 100.54 98. 51 96. 48 94.45 92.42 90.39 88 .36 86 .33 84 .29 82 .26 80 .23 78. 20 76.17 74.15 72.12 70. 08 68. 05 66.01 63. 98 61.95 59.9...

Ngày tải lên: 12/08/2014, 07:22

... less 3 /8 ¼ ¼ 1 /8 3 3 /8 5 /16 ¼ 5 /32 4 ½ 5 /16 ¼ 5 /32 5 5 /8 3 /8 5 /16 3 /16 6 ¾ 3 /8 3 /8 3 /16 7 and 8 1 ½ ½ ¼ 9 1¼ 5 /8 5 /8 5 /16 10 and 11 1½ ¾ ¾ 3 /8 12 and 13 ... 8 1 and 2 and 4 8 ½ 1 1 2 fluid ounces fluid ounces fluid ounces fluid ounces 2 4 8 16 32 ½ and 1 and 2 and 4 and 8 and 2 4 8...

Ngày tải lên: 12/08/2014, 07:22

... (Amended 1977, 1 986 , and 1 988 ) S.1.3.1. Minimum Height of Figures, Words, and Symbols. - The minimum height of the figures used to indicate the fare shall be 10 mm and for extras, 8 mm. The minimum ... Values. - Maintenance and acceptance tolerances for timing devices shall be as follows: T.1.1. For Timing Devices Other Than Those Specified in T.1.2. and T....

Ngày tải lên: 12/08/2014, 07:22

... Tolerances, and Other Technical Requirements for Weighing and Measuring Devices, and supplements thereto or revisions thereof, shall apply to commercial weighing and measuring devices in the ... weighing and measuring devices as recommended by the National Conference on Weights and Measures shall be the specifications, tolerances, and other tec...

Ngày tải lên: 12/08/2014, 07:22

... ambulances, and hearses.[5.53] performance requirements. Performance requirements include all tolerance requirements and, in the case of nonautomatic-indicating scales, sensitivity requirements ... medicinal and other formulas prescribed by physicians and others and used or intended to be used in the ordinary trade of pharmacists.[2.20] pressure type (device). A type...

Ngày tải lên: 12/08/2014, 07:22