Specifications, Tolerances, and Other Technical Requirements for Weighing and Measuring Devices Episode 6 pdf

... of Commerce Technology Administration National Institute of Standards and Technology SPECIFICATIONS, TOLERANCES, AND OTHER TECHNICAL REQUIREMENTS FOR WEIGHING AND MEASURING DEVICES as adopted by the 91st National Conference on Weights and Measures ... tolerances, and other technical requirements apply as follows: (a) To commercial weighing and measu...

Ngày tải lên: 27/06/2014, 18:20

... Specifications, Tolerances, and Other Technical Requirements for Weighing and Measuring Devices as adopted by the 91 st National Conference on Weights and Measures 20 06 Editors: ... 2003 and 20 06) G-S.1.1. Location of Marking Information for Not Built -For- Purpose, Software-Based Devices. - For not built- for- purpose, software-based devices e...

Ngày tải lên: 12/08/2014, 07:22

... 1.500 1.522 1 .64 7 1.798 1.959 22 1.529 1.544 1 .66 7 1.8 16 1.9 76 23 1.559 1. 566 1 .68 6 1.835 1.994 24 1.588 1.588 1.7 06 1.853 2.012 2.1 76 25 1 .61 8 1 .61 0 1.725 1.871 2.029 2.194 26 1 .63 2 1.745 1.890 ... 2.541 2 .69 1 2.849 3.011 55 2.314 2.423 2.559 2.708 2. 866 3.028 56 2.333 2.441 2.5 76 2.725 2.882 3.044 57 2.353 3 2. 460 2.594 2.742 2.899 3. 061 58 2.478 2 ....

Ngày tải lên: 12/08/2014, 07:22

... 1 /64 0.1 6 1 /32 0.3 19 1 / 16 0.4 26 1 /8 0.5 32 ¼ 1.0 65 ½ 1.5 97 1.0 65 1 1.7 110 1.0 65 2 2.0 130 1.0 65 3 2.0 130 1.5 97 4 3.0 190 1.5 97 1.0 65 5 3.5 230 1.5 97 1.0 65 6 3.5 ... trails shall use the format set forth in Table S.2.2.]* [*Nonretroactive and enforceable as of January 1, 1995] (Amended 1991, 1993, 1995, and 20 06) S.2.2.1. Multiple Measurin...

Ngày tải lên: 12/08/2014, 07:22

... following devices: (a) Devices used for dispensing liquefied petroleum gases (see Sec. 3.32; Code for Liquefied Petroleum Gas and Anhydrous Ammonia Liquid -Measuring Devices) , or other liquids ... exceed: (a) 20 L (5 gal) per minute for stationary retail devices, or (b) 20 % of the marked maximum discharge rate for other retail devices and for wholesale d...

Ngày tải lên: 12/08/2014, 07:22

... 0.71 0 .69 0 .67 0 .65 0 .63 0 .61 0.59 100.85 98.82 96. 79 94. 76 92.73 90.70 88 .66 86. 63 84 .60 82.57 80.54 78.51 76. 48 74.45 72.41 70.38 68 .35 66 .32 64 .29 62 . 26 60 .23 58.20 ... 2420 264 0 2 860 3080 3320 3 560 3800 4050 4310 4580 1.02 1.00 0.98 0. 96 0.94 0.92 0.90 0.88 0. 86 0.84 0.82 0.80 0.78 0. 76 0.74 0.72 0.70...

Ngày tải lên: 12/08/2014, 07:22

... inches minims 0 16 21 26 31 36 41 46 51 56 61 66 71 76 81 86 91 96 16 21 26 31 36 41 46 51 56 61 66 71 76 81 86 91 96 101 0.1 0.2 0.4 0 .6 0.8 1.1 1.4 ... 5 .6 6. 4 7.2 8.1 9.0 0 9 / 16 13 / 16 1 1 / 16 1 5 / 16 1 9 / 16 1 13 / 16 2 1 / 16 2 5 / 16 2 9 / 16 2 13 / 16 3 1 / 16...

Ngày tải lên: 12/08/2014, 07:22

... Values. - Maintenance and acceptance tolerances for timing devices shall be as follows: T.1.1. For Timing Devices Other Than Those Specified in T.1.2. and T.1.3. - The maintenance and acceptance ... indicate and record, if the device is equipped to record, the time in terms of minutes for time intervals of 60 minutes or less and in hours and minutes for time int...

Ngày tải lên: 12/08/2014, 07:22

... Tolerances, and Other Technical Requirements for Weighing and Measuring Devices, and supplements thereto or revisions thereof, shall apply to commercial weighing and measuring devices in the ... weighing and measuring devices as recommended by the National Conference on Weights and Measures shall be the specifications, tolerances, and other tec...

Ngày tải lên: 12/08/2014, 07:22

... ambulances, and hearses.[5.53] performance requirements. Performance requirements include all tolerance requirements and, in the case of nonautomatic-indicating scales, sensitivity requirements ... devices since they have no graduations. The verification scale division, e, may be different from the displayed scale division, d, for certain other devices used for weigh...

Ngày tải lên: 12/08/2014, 07:22