Mechanical Engineers Reference Book 12 Part 8 pps
Mechanical Engineers Reference Book 12 Part 8 pps
... thus et = -ucca. Equation (8. 29) now can be written as dR R - = F,(1 - ucKc)r, (8. 30) Comparing equations (8. 28) and (8. 30) gives F = Fa(l - u&) (8. 31) It is important to ... 10 98 76 5 4 3 2 10 12 3 4 5 6 78 910 Transverse sensitivity K, (%) Figure 8. 29 Errors due to transverse sensitivity of a strain gauge 8. 2.4 Strain gauge ar...
Ngày tải lên: 12/08/2014, 03:20
Mechanical Engineers Reference Book 12 Part 9 ppsx
... 25C500 140-250 80 - 140 30 -80 15 VG 22 32 46 68 100 150 220 32 VG 46 68 100 150 220 320 460 68 VG 100 150 220 320 360 680 1000 150 VG 220 320 460 680 1000 1000 ... > 0 .12 C) High demands on running accuracy with light loads (P S 0.06 C) Machine tools Axial loads only Bearing applications of all kinds ( 18) to 100 (100) to...
Ngày tải lên: 12/08/2014, 03:20
Mechanical Engineers Reference Book 12 Part 11 ppsx
... 151 0.93 1 48 0.92 145 0.91 142 0.90 139 0 .89 136 0 .88 133 0 .87 130 0 .86 127 0 .85 123 0 .83 120 0 .82 Nore: Arcs of contact below 120 " should not be used without confirmation ... 4.7 8. 0 7.0 32 463 6.2 36 >63 6.3 z-SPZ 8. 5 2.5 9.0 12. 0 8. 0 34 480 10.0 38 > ;80 10.2 A-SPA 11.0 3.3 11.0 15.0 10.0 34 41 18 13.1 38 >1 18 13.3 B-SPB...
Ngày tải lên: 12/08/2014, 03:20
Mechanical Engineers Reference Book 12 Part 15 ppsx
... ventiilators References 15/151 47 EH 40 /89 Occupational Exposure Limits, Health and Safety Commission (1 989 ) 48 Fuel Efficiency Booklets, Department of Energy (1 984 -1 986 ): 1. Energy ... Hydraulic Institute Standards (1 983 ) 14 BS 84 8, Fans for General Purposes Part 1: Methods of Testing Performance (1 980 ): Part 2: Methods of Noise Testing (1 985 ) 15 BS 2...
Ngày tải lên: 12/08/2014, 03:20
Mechanical Engineers Reference Book 12 Part 1 potx
... 0.6 0 .8 1.0 1.2 1.4 1.6 1 .8 2.0 2.2 2.4 2.6 2 .8 3.0 3.2 3.4 3.6 3 .8 4.0 0 0.1 585 0.31 08 0.4515 0.5763 0. 682 7 0.7699 0 .85 86 0 .89 04 0.9 281 0.9545 0.9722 0. 983 6 0.9907 ... 0. 983 6 0.9907 0.9949 0.9973 0.9 986 0.9993 0.9997 0.99 98 0.9999 1.0000 0 .84 15 0. 689 2 0.5 485 0.4237 0.3173 0.2301 0.1414 0.1096 0.0719 0.0455 0.0...
Ngày tải lên: 12/08/2014, 03:20
Mechanical Engineers Reference Book 12 Part 2 pptx
... the primary coil is El = Nl(d@dt) (2 .86 ) Since the magnetic flux is common to both coils the e.m.f. induced in the secondary winding is (2 .87 ) (2 .88 ) The ratio of primary coil turns ... system, i.e. Decimal 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Hexadecimal 0 1 2 3 4 5 6 7 8 9 A B C D E F Using hex notation then, 8- bit binary numbers may be re...
Ngày tải lên: 12/08/2014, 03:20
Mechanical Engineers Reference Book 12 Part 4 docx
... (CA) 106 (CB) 107 (CC) 1 08 (CD) 109 (CF) 1 10 (CG) 111 (CH) 113 (DA) 114 (DB) 115 (DD) 116 1 18 (SBA) 119 (SBB) 120 (SCA) 121 (SCB) 122 (SCF) 125 (CE) 126 140 141 142 Number ... semiconductor suppliers, ranging in size from 4 Kbytes to 1 28 Kbytes. In the latter form, very high density is achieved, with up to 1 28 megabytes of memory available on a single print...
Ngày tải lên: 12/08/2014, 03:20
Mechanical Engineers Reference Book 12 Part 5 pot
... interested parties. 6.1.7.1 Design: Examples BS 5070: 1974 Graphical symbols and diagrams BS 3 08: Part 1: 1 984 Engineering drawing practice (IS0 1 28 ): BS 3 08: Part 2: 1 985 Dimensioning (IS0 129 ) ... 80 0 - - - - -290 -160 - -80 - -24 0 80 0 1000 - - - - -320 -170 - -86 I - -26 0 1000 125 0 I - 1 - 1 - 1 - 1-3501-1951 - 1 - 98 I -...
Ngày tải lên: 12/08/2014, 03:20
Mechanical Engineers Reference Book 12 Part 14 doc
... temperature of 120 °C Assume system minimum return temperature of 65°C Increase in volume from 10°C to 65°C - - (999.7 - 980 .5) 200 000 980 .5 Increase in volume from 65°C to 120 °C ( 980 .5 - ... and condensation problems. ASME 1 989 Part 1 Power Boilers ASME 1 989 Part 2 Material Specification ASME 19139 Part 8 Pressure Vessel Division 1 Design Code 15....
Ngày tải lên: 12/08/2014, 03:20