Marine Machinery 7 E Part 11 docx

Ngày tải lên: 13/12/2013, 19:15

Ngày tải lên: 14/12/2013, 14:15

Ngày tải lên: 14/12/2013, 14:15

... phương thứ c GetType() mà mọi lớp đều có thể truy xuất một đối tượng Type tượng trương cho kiểu dữ liệu của lớp. Chúng ta dùng đối tượng này để trả về tên namespace cho lớp. using System;

Ngày tải lên: 15/12/2013, 02:15

... Jersey Institute of Technology, Bearing and Bearing Lubrication Laboratory. The testing apparatus is similar to that shown in Fig. 14-7, and the test bearing is UHMWPE journal bearing against stainless ... been a significant improvement in bearings in machinery, but the design of the hip replacement joint remains basically the same. This is an example where engineering design...

Ngày tải lên: 21/07/2014, 17:20

... and to remove waste matter created during the chemical reaction when the phosphates stored in the muscles degenerate to create energy. 3.9.2.4 Spinal column In the process of evolution, the bony ... a workplace where, at the design stage, little if any thought had been given to ergonomic issues. Even where consideration has been given at the design stage improvements can still be made. Ge...

Ngày tải lên: 11/08/2014, 21:21

... Avenue, Woburn, MA 018 01- 20 41 First published 19 52 Reprinted 1 976 ,1 979 Second edition 19 55 Sixth edition 19 83 Third edition 19 63 Reprinted 19 87 Fourth edition 19 68 Seventh edition 19 95 Reprinted ... from the main condenser (Figure 1. 13) by an air ejector, cooled by the main condensate and released in the ejector condenser. The condensed ejector...

Ngày tải lên: 12/08/2014, 02:22

... lines. Detergent oils are, therefore, widely used in this type of engine, The detergent additives used today are, in most cases, completely soluble in the oil. There is a tendency ... robust reciprocating or gear pump. The system must be protected by a relief arrangement. Pre-treatment and post-treatment Sea-water feed for reverse osmosis plant, is pretreated...

Ngày tải lên: 12/08/2014, 02:22

... skin. The effects and remedies are so diverse that reference books are needed on chemical carriers, to summarize the dangers and to give the correct response. Bulk liquid chemicals ... have been used. Because of the corrosive nature of the gas the fan materials must be carefully selected. Fan impellers of stainless steel or nickel-aluminium bronze are frequen...

Ngày tải lên: 12/08/2014, 02:22

... checked by measuring the diameter of the outer sleeve before and after tightening. The diameter increase should agree with the figure stamped on the sleeve. To disconnect the coupling, ... sandwiched between the propeller hub and the liner end. It is essential that the rubber has freedom to flow when nipped between the hub and liner. Excessive weardown of be...

Ngày tải lên: 12/08/2014, 02:22

... (Figure 8. 30) is necessary between the medium-speed diesel and the reduction gear. The coupling is necessary because the periodic application and reduction of torque as engine ... Figure 8. 27 Hub with cast iron sleeve 282 The propeller shaft Figure 8. 29 Reverse/reduction gearbox arrangement The drive from the engine input shaft to the counter shaf...

Ngày tải lên: 12/08/2014, 02:22

... temperature is the temperature registered by a thermometer with wetted fabric around the bulb. (When moisture evaporates from a surface, i .e. the skin, the latent heat required, ... thermometers suspended from screwed plugs in vertical steel tubes with perforations hung in the cold chamber have been replaced by remote reading devices. Electrical resistance and ele...

Ngày tải lên: 12/08/2014, 02:22

... portable fire extinguisher. A fire which develops undetected in an unmanned machinery space (or one where the watchkeeper is Deck machinery and cargo equipment 4 07 conventional derrick ... (Figure 14.10) of different thickness. These are set up parallel to each other and arranged to deflect in the same direction. Rapid temperature rise will cause the...

Ngày tải lên: 12/08/2014, 02:22

... 93—105 Turbo-feed pump, Weir type, 32 -7 Water-boxes, 1 Two-ram electro-hydraulic steering gear, Watertight doors 468 -71 288-90, 299-301 Weir electrofeeder, 38 Two stage air ejector, 22—4 Weir ... loads, evaluation of, fire risk, 53-55 372 -7 fuel heater, 66-8 Heat leakage, 365-6 heating, 66-8 Hele-Shaw pump, 290—2 homogenizer, 68 70 Hermetic compressors, 349...

Ngày tải lên: 12/08/2014, 02:22