Nondestructive Evaluation and Quality Control (1998) Part 6 doc

... 25, 13, and 10 mm (1, , and in.) correspond to typical search-unit sizes, and values for radiators with diameters of 3 and 1.5 mm ( and 0. 060 in.) correspond to typical hole sizes in standard ... acoustic impedance and amplitude of particle motion. The acoustic pressure exerted by a given particle varies in the same direction and with the same frequency as the position of t...

Ngày tải lên: 12/08/2014, 02:20

... Fig. 16( b) and 16( c) show large peaks in AE count rate near the rupture strains of the major brittle components (titanium diboride in B(B 4 C)/Ti-6Al-4V and titanium carbide in SiC/Ti-6Al-4V). ... Plants Using Nondestructive Testing and Electrochemical Methods, STP 908, G.C. Moran and P. Labine, Ed., American Society for Testing and Materials, 19 86, p 43-47 40. P. Pantu...

Ngày tải lên: 12/08/2014, 02:20

... useful in design and calibration and process control procedures, in establishing the characteristics and performance of materials and equipment used, in anticipating the problems and controls necessary ... 223 205 277 15 0. 56 0.022 165 4 3319 1289 29 1 .65 0. 065 4095 4095 264 8 33 0.08 0.003 (a) (a) (a) 25 0.25 0.010 66 9 565 824 32 0...

Ngày tải lên: 12/08/2014, 02:20

... of nondestructive examination and analysis of materials and manufactured parts and assemblies is not new to Metals Handbook. In 19 76, Volume 11 of the 8th Edition Nondestructive Inspection and ... through a thorough understanding of modern techniques for nondestructive evaluation and statistical analysis can product reliability and quality control be achieved and...

Ngày tải lên: 12/08/2014, 02:20

... Gold 24.4 70 Aluminum 28.2 61 Aluminum alloys 60 61-T6 41 42 7075-T6 53 32 2024-T4 52 30 Magnesium 46 37 70-30 brass 62 28 Phosphor bronzes 160 11 Monel 482 3 .6 Zirconium 500 3.4 Zircaloy-2 ... James and O. Buck, Quantitative Nondestructive Measurements of Residual Stresses, CRC Crit. Rev. Solid State Mater. Sci., Vol 9, 1980, p 61 2. C.O. Ruud, "Review and...

Ngày tải lên: 12/08/2014, 02:20

... incident and reflected waves interfere and cause a standing wave. The standing wave wavelength and peak amplitude change along the standing wave pattern and are related to the velocity and attenuation ... 30, July 1951, p 564 -587 6. E.N. Leith and J. Upatnieks, Photography by Laser, Sci. Am., Vol 212 (No. 6) , June 1 965 , p 24 7. G.W. Stroke, An Introduction to Current...

Ngày tải lên: 12/08/2014, 02:20

... Biol., Vol 36, 1972, p 105-117 56. G.T. Herman and A. Lent, Iterative Reconstruction Algorithms, Comput. Biol. Med., Vol 6, 19 76, p 273- 294 Neutron Radiography Harold Berger, Industrial Quality, ... Reference cited in this section 6. L.E. Bryant and P. McIntire, Ed., Radiography and Radiation Testing, in Nondestructive Testing Handbook, Vol 3, American Society for Nond...

Ngày tải lên: 12/08/2014, 02:20

... Methods of Evaluation, Foundryman Int., April 1988, p 1 96- 209 Horizons in Powder Metallurgy, 19 86 International Powder Metallurgy Conference Proceedings, Part II, p 763 16. M.P. Jones and G.V. ... promising techniques for the nondestructive evaluation of both green and sintered P/M parts. In addition to detecting cracks in green parts, as well as part- to -part den...

Ngày tải lên: 12/08/2014, 02:20

... incident and reflected waves interfere and cause a standing wave. The standing wave wavelength and peak amplitude change along the standing wave pattern and are related to the velocity and attenuation ... the medium bands; and plastics and composite materials such as filament-wound glass, Kevlar, and honeycomb in the higher bands. References cited in this section 17....

Ngày tải lên: 10/08/2014, 13:20

... Properties and selection v. 2. Properties and selection nonferrous alloysand pure metals [etc.] v. 17. Nondestructiveevaluation and quality control. 1. Metals Handbooks, manuals, etc. I. ASM Handbook ... two major roles: quality control and process control. In the area of quality control, CMMs can generally perform traditional final part inspection more accurately, mo...

Ngày tải lên: 10/08/2014, 13:20