Root Cause Failure Analysis Part 11 ppsx
Root Cause Failure Analysis Part 11 ppsx
... 166 Root cause, 4, 5, 14 Root cause failure analysis, 19 Rotary compressors, 130, 257 Rotary pumps, 244 Rotating speed, 96 Safety, 10, 11, 12, 13, 23, 27,58 Screw conveyors, 117 ... or blowers. (1) A cause of an event. (2) The cause of each discrete frequency component in a machine train’s vibration signature. 298 Root Cause Failure Analysis lon...
Ngày tải lên: 11/08/2014, 21:23
Root Cause Failure Analysis Part 1 ppsx
... increased difficulty is that the cause often is subjective. ROOT CAUSE FAILURE ANALYSIS Part I INTRODUCTION TO ROOT CAUSE FAILURE ANALYSIS ROOT CAUSE FAILURE ANALYSIS R. Keith Mobley ... that leads to failure. Instead, it displays all the possible causes that CONTENTS Part I Introduction to Root Cause Failure Analysis Chapter 1 Introduction...
Ngày tải lên: 11/08/2014, 21:23
Root Cause Failure Analysis Part 2 ppt
... potential root causes to verify each of the suspect causes is essential. In almost all cases, a relatively simple, inexpensive test series can be devel- Root Cause Failure Analysis Methodology ... use not enforced L.C"f?%EF-) Figure 3-9 Common root causes of procedure-related problems. 46 Root Cause Failure Analysis 4 Polides and Procedures No s...
Ngày tải lên: 11/08/2014, 21:23
Root Cause Failure Analysis Part 3 pptx
... selected with care. 77 56 Root Cause Failure Analysis Causes and Long-Term Corrective Actions This section of the report should clearly describe the specific root cause( s) that hig- gered ... Distractions caused by personal problems are a leading cause of work-related acci- dents. However, extreme caution must be exercised when trying to ascertain if it was a Root Cau...
Ngày tải lên: 11/08/2014, 21:23
Root Cause Failure Analysis Part 5 pdf
... manifold with posi- 140 Root Cause Failure Analysis Figure 1& ;11 kaf spring configuration (Gibbs 1971). the rod. The amount of heat generated can be considerable, particularly when moderate ... reduced maintenance. Cooling, particularly water cooling, maintains a more even temperature around the cylinder bore and reduces warpage. 114 Root Cause Failure Analys...
Ngày tải lên: 11/08/2014, 21:23
Root Cause Failure Analysis Part 6 pot
... 148 Root Cause Failure Analysis Figure 11- 1 Top-entering propeller-type mixer (Thomas Register 1995). Figure 11- 2 Side-entering propeller-type mixer (Thomas Register 1995). 168 Root Cause ... prevent stress failure. Smaller- diameter rolls can be reduced in a single step, but they also must have stress relief by undercutting to prevent failure. 144 Root Cause...
Ngày tải lên: 11/08/2014, 21:23
Root Cause Failure Analysis Part 7 potx
... drive. This factor compensates for the variation in speed, or slip, caused by load changes. 194 172 Root Cause Failure Analysis Table 161 Gear Characteristics Overview Gear Type Characteristics ... quick steam-sys- tem startup because they continuously purge the system of air and other noncondens-
Ngày tải lên: 11/08/2014, 21:23
Root Cause Failure Analysis Part 8 pot
... valve. Because of heat buildup, solenoid actuators must be limited to short-duration activation. A brief burst of electrical energy is transmitted to the sole- 212 Root Cause Failure Analysis ... valve is designed to operate an I1 12 B Y3 il Figure 17 -11 Three-way, fluid-power valve (Nelson 1986). 206 Root Cause Failure Analysis Straight - flow Angle - flo...
Ngày tải lên: 11/08/2014, 21:23
Root Cause Failure Analysis Part 9 pdf
... Root Cause Failure Analysis Table 21-1 Common Failure Modes of Pneumatic Conveyors I THE CAUSES Piping Configuratkn Unsuitable IPiping Leakage4 240 Root Cause Failure Analysis ... axial thrusting caused by the frequent variations in suction or discharge pressure caused by the stadstop operation. 244 Root Cause Failure Analysis Table 19-2 Common F...
Ngày tải lên: 11/08/2014, 21:23
Root Cause Failure Analysis Part 10 pdf
... Table 23-1 Common Failure Modes of Mixers and Agitators Source: Integrated Systems, Inc. 286 Root Cause Failure Analysis Table 31-1 Common Failure Modes of Wear Part Surfaces Source: ... directly affect the gears. The change in load zone caused by the misaligned driven 270 Root Cause Failure Analysis Table 25-1 Common Failure Modes of Process Rolls...
Ngày tải lên: 11/08/2014, 21:23