The Motor Vehicle 2010 Part 16 pot

The Motor Vehicle 2010 Part 16 pot

The Motor Vehicle 2010 Part 16 pot

... markings The aspect ratio is the inverse of the ratio of the width to the height of the crown of the tyre above the edge of the bead that seats on the rim. Modern 1086 The Motor Vehicle the tyre. ... influenced to a major extent by the geometry of the bump and the speed of the vehicle, while the major influence on the latter, apart from the geometry...

Ngày tải lên: 11/08/2014, 20:21

70 368 0
The Motor Vehicle 2010 Part 5 potx

The Motor Vehicle 2010 Part 5 potx

... pulley on the front end of the crankshaft. On the other hand, the oil pump is interposed between the toothed wheel for the HTD drive and the crankcase wall and driven by a gear on the crankshaft. ... HTD toothed belt drive from the crankshaft to the injection pump and overhead camshaft. The alternator on the side of the crankcase, and the spindle of the fan an...

Ngày tải lên: 11/08/2014, 20:21

70 281 0
The Motor Vehicle 2010 Part 12 potx

The Motor Vehicle 2010 Part 12 potx

... If the accelerator pedal is further depressed the balance will be upset and the valve will move to the left, the part C will then uncover the inlet port from the pump and the pressure in the ... On the other hand, if the accelerator pedal is released a little then the oil pressure on the left-hand end of the valve will move the valve to the right, thus uncove...

Ngày tải lên: 11/08/2014, 20:21

70 279 0
The Motor Vehicle 2010 Part 14 pot

The Motor Vehicle 2010 Part 14 pot

... that other things being equal the smaller the height OG the less the overturning couple. The magnitude of the righting couple QQ is Q × SS, so that the greater the wheelbase SS the less the force ... between the wedge and the plungers and these are kept in place by a cage carried on the end of the wedge. The whole assembly is clamped to the backplate F of the...

Ngày tải lên: 11/08/2014, 20:21

70 298 0
The Motor Vehicle 2010 Part 2 doc

The Motor Vehicle 2010 Part 2 doc

... over the end of the stem, seating its rim on the retainer washer for the spring, so that there is a small clearance between the tip of the stem and the other end of the thimble. When the cam ... camshaft. The exhaust valves are inclined 16 to one side of the axis of the cylinder and the inlets 19° to the other side. Their seats are in a penthouse-type combustio...

Ngày tải lên: 11/08/2014, 20:21

70 463 0
The Motor Vehicle 2010 Part 3 ppt

The Motor Vehicle 2010 Part 3 ppt

... filter to the engine, while the other half passes through the relief valve, which lifts at 483 kN/m 2 , to the oil cooler integral with the filter housing at the front end of the sump. The return ... the first part, the overlap period, of the valve lift, it restricts the area of the orifice. This limits the quantity of fuel injected during the combustion dela...

Ngày tải lên: 11/08/2014, 20:21

70 209 0
The Motor Vehicle 2010 Part 4 docx

The Motor Vehicle 2010 Part 4 docx

... of the governor assembly. To transmit the drive from the drive shaft to the rotor, a tongue in the end of the latter registers in a slot in the end of the drive shaft. The arrangement of the ... pulls the strip, or fuel adjustment plate, down on the two contact lines 6 on the rotor head. The ends of the adjustment plate limit the outward movement of the p...

Ngày tải lên: 11/08/2014, 20:21

70 383 0
The Motor Vehicle 2010 Part 6 ppsx

The Motor Vehicle 2010 Part 6 ppsx

... pump 380 The Motor Vehicle bleed hole in the plug in the end of the passage delivering the fuel to the emulsion tube not only helps to emulsify the extra fuel supplied and to regulate the flow ... of these was the small duct D, which drew fuel from the starter well integral with the float chamber shown in the sectioned view on the right. The other was the muc...

Ngày tải lên: 11/08/2014, 20:21

70 303 0
The Motor Vehicle 2010 Part 7 doc

The Motor Vehicle 2010 Part 7 doc

... senses the passage of either a pin or hole in the flywheel. These two signals are processed in the control unit to make them compatible with the computer. The parameters on the basis of which the ... mostly forced at the speed of rotation of the engine. The delivery pressure in the pipelines to the nozzles is determined by the capacity of the accumulator, the rat...

Ngày tải lên: 11/08/2014, 20:21

70 259 0
The Motor Vehicle 2010 Part 9 ppsx

The Motor Vehicle 2010 Part 9 ppsx

... remain by the time it reaches the vehicle. Therefore, if vehicle fuel-system protection is required too, the treatment must be heavier. As in the case of the detergents, the polar heads attach themselves ... of the casing, where it enters the spaces between, one after the other in turn, the spiral grooves on the female and their meshing lobes on the male rotor. This...

Ngày tải lên: 11/08/2014, 20:21

70 289 0
w