The Motor Vehicle 2010 Part 12 potx

... If the accelerator pedal is further depressed the balance will be upset and the valve will move to the left, the part C will then uncover the inlet port from the pump and the pressure in the ... On the other hand, if the accelerator pedal is released a little then the oil pressure on the left-hand end of the valve will move the valve to the right, thus uncove...

Ngày tải lên: 11/08/2014, 20:21

... pulley on the front end of the crankshaft. On the other hand, the oil pump is interposed between the toothed wheel for the HTD drive and the crankcase wall and driven by a gear on the crankshaft. ... HTD toothed belt drive from the crankshaft to the injection pump and overhead camshaft. The alternator on the side of the crankcase, and the spindle of the fan an...

Ngày tải lên: 11/08/2014, 20:21

... over the end of the stem, seating its rim on the retainer washer for the spring, so that there is a small clearance between the tip of the stem and the other end of the thimble. When the cam ... between the flat area surrounding the slightly dished portion of the crown of the piston and the flat lower face of the casting, each side of the pairs of valves. B...

Ngày tải lên: 11/08/2014, 20:21

... filter to the engine, while the other half passes through the relief valve, which lifts at 483 kN/m 2 , to the oil cooler integral with the filter housing at the front end of the sump. The return ... the first part, the overlap period, of the valve lift, it restricts the area of the orifice. This limits the quantity of fuel injected during the combustion dela...

Ngày tải lên: 11/08/2014, 20:21

... of the governor assembly. To transmit the drive from the drive shaft to the rotor, a tongue in the end of the latter registers in a slot in the end of the drive shaft. The arrangement of the ... shown in the illustration, is mounted on the upper end of the vertical spindle 12. This is actuated by linkage to the accelerator pedal. On the lower end of the s...

Ngày tải lên: 11/08/2014, 20:21

... pump 380 The Motor Vehicle bleed hole in the plug in the end of the passage delivering the fuel to the emulsion tube not only helps to emulsify the extra fuel supplied and to regulate the flow ... of these was the small duct D, which drew fuel from the starter well integral with the float chamber shown in the sectioned view on the right. The other was the muc...

Ngày tải lên: 11/08/2014, 20:21

... above the previously mentioned hole, into the manifold. The gap between the lower end of the tube and the upper edge of the hole is set during manufacture as follows. The lower end of the nozzle ... mostly forced at the speed of rotation of the engine. The delivery pressure in the pipelines to the nozzles is determined by the capacity of the accumulator, the...

Ngày tải lên: 11/08/2014, 20:21

... use. One is the research octane number (RON) and the other the motor octane number (MON). There is also a third, applicable to the vehicle rather than the fuel, and this is termed the road octane ... it enters the spaces between, one after the other in turn, the spiral grooves on the female and their meshing lobes on the male rotor. This is the induction phase of...

Ngày tải lên: 11/08/2014, 20:21

... B is thus the fixed member of the epicyclic train, the gear A is the driving member and the planet carrier and wheel are thus driven at half the speed of the halfshaft. 884 The Motor Vehicle 31.7 ... equal to P/2. The reactions of the forces acting on the ends of the beam act on the discs, hence equal forces are applied to the discs at equal distances from thei...

Ngày tải lên: 11/08/2014, 20:21

... that other things being equal the smaller the height OG the less the overturning couple. The magnitude of the righting couple QQ is Q × SS, so that the greater the wheelbase SS the less the force ... between the wedge and the plungers and these are kept in place by a cage carried on the end of the wedge. The whole assembly is clamped to the backplate F of the...

Ngày tải lên: 11/08/2014, 20:21