The Motor Vehicle 2010 Part 2 doc

... over the end of the stem, seating its rim on the retainer washer for the spring, so that there is a small clearance between the tip of the stem and the other end of the thimble. When the cam ... between the flat area surrounding the slightly dished portion of the crown of the piston and the flat lower face of the casting, each side of the pairs of valves. B...

Ngày tải lên: 11/08/2014, 20:21

... and systems 24 6 The Motor Vehicle Fig. 6. 62 The pressure regulator valve the upper end of the injector body, Fig. 6.63. By virtue of the facts that the injector does not perform the pressurisation ... of the governor assembly. To transmit the drive from the drive shaft to the rotor, a tongue in the end of the latter registers in a slot in the end of th...

Ngày tải lên: 11/08/2014, 20:21

... coaxially but with their cranks at 90° to each other, are the most common layouts. Their firing orders are 1 5 2 6 4 8 3 7 and 1 6 2 8 4 3 7 5 458 The Motor Vehicle the torque of the engine can be ... between their moving parts. Another significant advantage is that the working cylinders operate with the throttle opened wider, and there is no throttling of the idle cylin...

Ngày tải lên: 11/08/2014, 20:21

... m) 300 24 0 28 0 80 120 110 70 100 60 90 80 50 70 40 60 30 50 40 23 0 22 0 21 0 20 0 1000 120 0 1400 1600 1800 20 00 22 00 24 00 26 00 1000 120 0 1400 1600 1800 20 00 22 00 24 00 26 00 Engine ... (bhp) 160 50 140 120 40 100 30 80 60 20 24 0 23 0 22 0 21 0 79 kW (106 bhp) 354 N m (26 1 lbf ft) 360 26 0 340 24 0 320 26 0 387 N m (28 5 lbf f...

Ngày tải lên: 11/08/2014, 20:21

... VII 92 mm 120 mm MK.VI 92 mm 120 mm Spec. fuel con. MK.I 85 mm 120 mm B.M.E.P. B.M.E.P. 0 .22 engine performance 800 1000 120 0 1400 1600 1800 20 00 22 00 curves Rev/min 333 The two-stroke ... of 20 3 .2 mm giving a swept volume of 326 2 cm 3 . At 24 00 rev/min the maximum output of 78.3 kW is obtained, correspond- ing to a bmep of 414 kN/m 2 . The maximum...

Ngày tải lên: 11/08/2014, 20:21

... flat bimetal thermostat spring. It senses the temperature of the body of the carburettor and regulates Fig. 11 .26 Stromberg CD carburettor 408 The Motor Vehicle to the underside of the air valve ... pump 380 The Motor Vehicle bleed hole in the plug in the end of the passage delivering the fuel to the emulsion tube not only helps to emulsify the extra fuel su...

Ngày tải lên: 11/08/2014, 20:21

... groove, at the inlet end, and thereafter progressively compresses and displaces the air towards the far end of the casing. Finally, the delivery 12 10 8 6 4 2 0 20 30 40 50 60 70 80 350 26 0 27 5 300 400 80% ... Ltd) 626 The Motor Vehicle are nominally in contact, they are in fact held apart by the peaks of their microscopic roughness. A proportion of these peaks pre...

Ngày tải lên: 11/08/2014, 20:21

... If the accelerator pedal is further depressed the balance will be upset and the valve will move to the left, the part C will then uncover the inlet port from the pump and the pressure in the ... moves to the left. The transition valve is moved rapidly 8 42 The Motor Vehicle The layout of the gearbox is shown in Fig. 29 .1; there are four bevel gears S 1, S...

Ngày tải lên: 11/08/2014, 20:21

... differential N R P Q K X E 1 J L S B F 1 C A B L J X E 2 F 2 A D M O G H G P 2 P 2 P Fig. 31.1 Fig. 31 .2 The actual speed of the wheel F 1 will then be 20 2 rev/min, because its forward motion of 2 rev/min relatively to the differential ... appears as a pressure between the bevel pinion and its pin while the forces P /2 appear as pressures between the teeth of the...

Ngày tải lên: 11/08/2014, 20:21

... that other things being equal the smaller the height OG the less the overturning couple. The magnitude of the righting couple QQ is Q × SS, so that the greater the wheelbase SS the less the force ... between the wedge and the plungers and these are kept in place by a cage carried on the end of the wedge. The whole assembly is clamped to the backplate F of the...

Ngày tải lên: 11/08/2014, 20:21