Wiley SolidWorks 2009 Bible Part 7 potx
Wiley SolidWorks 2009 Bible Part 7 potx
... those parts, and will cause problems with any in-context features.
If you suppress the “ground” part or any part that connects groups of parts, keep in mind that this
can cause other parts to ... Locate the part at the assembly Origin such that
the part Origin matches the assembly Origin.
6. Open the part called Chapter 15 Patterned Part. sldprt, and place it in the
assembly....
Wiley SolidWorks 2009 Bible Part 15 potx
... sketches for, 77 2
tutorial, 78 3 78 7
using Combine features option with, 76 2 76 4
using Cut feature with, 77 5
using Delete Body feature with, 77 4 77 5
using Feature Scope with, 77 3 77 5
using Indent ... anchor, setting, 73 4
Table Driven pattern, features of, 301–303
table types
BOM (Bill of Materials), 73 3 73 7
design, 72 6 72 8
general, 73 3
hole, 72 8 73 1, 73 7 73 9
rev...
Wiley SolidWorks 2009 Bible Part 13 potx
... designers often use the first part of the
process to apply draft to parts. Tooling engineers often need to add or correct draft to plastic parts
they receive from part designers without draft ... Animations to Flex Parts
You cannot change part dimensions when animating. You cannot use features like the Flex to bend
parts for an animation. If you can’t do any of this, how do you make...
Wiley SolidWorks 2009 Bible Part 1 pdf
... 572
Task pane 572
Design Library 573
Other Design Library functions 577
Annotations 577
Location of the Design Library folder 577
Library parts 578
Sheet metal forming tools 578
Assemblies 579
Routing ... Folders 371
Using the Flyout FeatureManager 371
Summarizing Part Modeling Best Practice 373
Using Evaluation Techniques 377
Verification on rebuild 377
Check 378
Reflective...
Wiley SolidWorks 2009 Bible Part 2 doc
... use the Copy Settings Wizard, follow these steps:
1. Close SolidWorks.
2. Click Start ➪ Programs ➪ SolidWorks 2009 ➪ SolidWorks 2009 Tools ➪ Copy
Settings Wizard.
3. Select Save Settings, ... sure that it is
there.
64
SolidWorks Basics
Part I
NOTE
NOTE
You may need to have administrator access to your computer to apply a SolidWorks
registry file.
The SolidWorks setting...
Wiley SolidWorks 2009 Bible Part 3 docx
... setting. Figure 5.19 shows a sample part with
all three settings.
176
SolidWorks Basics
Part I
FIGURE 5.20
The Color and Optics interface elements
138
SolidWorks Basics
Part I
NOTE
NOTE
Using the Add ... with part and assembly
models but not drawings.
158
SolidWorks Basics
Part I
FIGURE 5.2
Scrollbars and splitters
Using the Magnifying Glass
A new visualization aid introd...
Wiley SolidWorks 2009 Bible Part 4 doc
... the part; the rest of the part is mirrored.
255
Selecting Features
7
ON
the
CD-ROM
ON
the
CD-ROM
The model used for this image can be found on the CD-ROM, with the filename
Chapter 7 Plastic ... FIGURE 7. 45
Using curvature combs to evaluate transitions
Lines and arc
non-continuous curvature
Lines and spline
continuous curvature
216
Building Intelligence into Your Parts
Part...
Wiley SolidWorks 2009 Bible Part 5 pot
... you are editing a part in inches, and enter 40mm, then SolidWorks does the conversion
for you. You can even mix units in a single expression such as 4. 875 +3.5mm, where the inch part
is assumed ... tables
Tutorial: Working with
configurations and design
tables
Working with Part
Configurations
302
Building Intelligence into Your Parts
Part II
FIGURE 8.18
Using a sketch-driven...
Wiley SolidWorks 2009 Bible Part 6 ppt
... the part
itself.
Starting with SolidWorks 2009, features created in the assembly can be propagated to reside in the
affected parts.
Component patterns
Component patterns can pattern either parts ... is particu-
larly important for SolidWorks users from many different fields
who need or want to make parametric relations between parts.
A lot of erroneous information floats around t...
Wiley SolidWorks 2009 Bible Part 8 ppt
... Data \SolidWorks\ SolidWorks 2009\ Design Library
\. You should store them in another
location, not in the SolidWorks installation directory, but in an area that you have selected to
maintain SolidWorks ...
shown in Figure 17. 38.
FIGURE 17. 38
The finished Assembly FeatureManager interface
554
Creating and Using Libraries
Part IV
FIGURE 17. 21
The User Settings page
FIGURE 17. 2...
Từ khóa: