Wiley SolidWorks 2009 Bible Part 4 doc

... works for 2D sketches; 3D sketches can be opened, but not closed this way. 244 Building Intelligence into Your Parts Part II Tangent propagation By default, fillets have the Tangent Propagation ... Extrude-Boss1 or Extrude-Cut1. The “Base” part of the Extruded Boss/Base is a holdover from when SolidWorks did not allow mul- tibody parts, and the first feature in a part had special...

Ngày tải lên: 11/08/2014, 18:20

... these steps: 1. Close SolidWorks. 2. Click Start ➪ Programs ➪ SolidWorks 2009 ➪ SolidWorks 2009 Tools ➪ Copy Settings Wizard. 3. Select Save Settings, and click Next. 4. Enter a location and ... make sure that it is there. 64 SolidWorks Basics Part I NOTE NOTE You may need to have administrator access to your computer to apply a SolidWorks registry file. The SolidWo...

Ngày tải lên: 11/08/2014, 18:20

... be grayed out if any SolidWorks docu- ments are open (so you must close all SolidWorks documents to change it). When you zoom in such that the part/ assembly/drawing is partially off the screen, ... over one of the splitters. 142 SolidWorks Basics Part I 1. From the CD-ROM, open the part named Chapter5Frame.sldprt. With the part open, click the Make Assembly From Part/ Asse...

Ngày tải lên: 11/08/2014, 18:20

... shallower. Starting with the 2009 release of the software, SolidWorks allows you to have angled faces on side edges, and will maintain the angle when it flattens the part. In previous versions, ... Base Flange Method for Sheet Metal Parts 29 Placing a forming tool To place a forming tool on a sheet metal part (forming tools are only allowed to be used on parts with sheet metal featur...

Ngày tải lên: 11/08/2014, 18:20

... freedom, 43 2 43 5 distance, 44 1 editing, 44 6 44 7 Gear, 43 9 Hinge, 44 4 44 5 and in-context, 511 InPlace, 49 7 49 8 Limit, 44 1 Linear Coupler, 44 3 44 4 Mechanical, 43 6 organizing with folders, 41 5 41 6 Path, ... 41 5 41 6 Path, 44 2 44 3 peg-in-hole, 43 0 43 1 positioning assemblies with, 46 8 46 9 Rack and Pinion, 44 0 references, 43 1 repairing missing references, 4...

Ngày tải lên: 11/08/2014, 17:22

... Coupler mate 44 3 Hinge mate 44 4 Belt/Chain 44 4 Editing and Troubleshooting 44 5 Editing existing mates 44 6 Troubleshooting 44 7 Distinguishing between the warnings and the errors 44 7 Examining ... motion 43 3 Working with Advanced and Mechanical Mate Types 43 5 Symmetric mate 43 6 Cam mate 43 6 Width mate 43 8 Gear mate 43 9 Rack and Pinion mate 44 0 Limit mates 44 1 Screw...

Ngày tải lên: 11/08/2014, 18:20

... editing a part in inches, and enter 40 mm, then SolidWorks does the conversion for you. You can even mix units in a single expression such as 4. 875+3.5mm, where the inch part is assumed as the document ... when you are using SolidWorks to model parts. SolidWorks remembers the Bill of Materials options and Advanced options that you set for the Default configuration and uses th...

Ngày tải lên: 11/08/2014, 18:20

... between parts and assemblies. CROSS-REF CROSS-REF Equations are discussed in detail in Chapter 9. 40 4 Working with Assemblies Part III Folders You can create folders to organize and group both parts ... the part itself. Starting with SolidWorks 2009, features created in the assembly can be propagated to reside in the affected parts. Component patterns Component patterns can patte...

Ngày tải lên: 11/08/2014, 18:20

... pattern. FIGURE 15.5 The component right-mouse button menu 47 4 Working with Assemblies Part III FIGURE 14. 14 Exploding the base The Tower part is a little more difficult because it is not lined ... those parts, and will cause problems with any in-context features. If you suppress the “ground” part or any part that connects groups of parts, keep in mind that this can cause other...

Ngày tải lên: 11/08/2014, 18:20

... folders are found at C:\Documents and Settings\All Users\ Application Data \SolidWorks\ SolidWorks 2009\ Design Library \. You should store them in another location, not in the SolidWorks installation ... Be careful about your choice of top-stack washers. 542 Creating and Using Libraries Part IV If you replace your Toolbox parts with the Toolbox parts from the client, you may experien...

Ngày tải lên: 11/08/2014, 18:20