Wiley SolidWorks 2009 Bible Part 3 docx

Wiley SolidWorks 2009 Bible Part 3 docx

Wiley SolidWorks 2009 Bible Part 3 docx

... setting. Figure 5.19 shows a sample part with all three settings. 176 SolidWorks Basics Part I FIGURE 5.20 The Color and Optics interface elements 138 SolidWorks Basics Part I NOTE NOTE Using the Add ... with part and assembly models but not drawings. 158 SolidWorks Basics Part I FIGURE 5.2 Scrollbars and splitters Using the Magnifying Glass A new visualization aid introd...
Ngày tải lên : 11/08/2014, 18:20
  • 80
  • 188
  • 0
Wiley SolidWorks 2009 Bible Part 15 potx

Wiley SolidWorks 2009 Bible Part 15 potx

... anchor, setting, 734 Table Driven pattern, features of, 30 1 30 3 table types BOM (Bill of Materials), 733 – 737 design, 726–728 general, 733 hole, 728– 731 , 737 – 739 revision, 731 – 733 , 739 –740 table-based ... 821–822 tutorial, 830 – 834 master model functions, file management of, 826 master model tools Insert Into New Part, 8 23, 826–827, 831 – 832 Insert Part, 8 23 826, 830 –...
Ngày tải lên : 11/08/2014, 17:22
  • 25
  • 212
  • 0
Wiley SolidWorks 2009 Bible Part 1 pdf

Wiley SolidWorks 2009 Bible Part 1 pdf

... Phantom 38 2 SimulationXpress 38 2 Material 38 3 Restraint 38 3 Load 38 4 Analyze 38 4 Results 38 4 Optimization 38 5 Tutorial: Making Use of Editing and Evaluation Techniques 38 6 Summary 39 3 Part III: ... reference 930 Terminating ribs 930 Using thin features 932 Using Draft 933 Neutral Plane draft 933 Parting Line draft 934 Step draft 934 Some draft limitations 935 Wha...
Ngày tải lên : 11/08/2014, 18:20
  • 80
  • 285
  • 0
Wiley SolidWorks 2009 Bible Part 2 doc

Wiley SolidWorks 2009 Bible Part 2 doc

... Figure 2 .38 . FIGURE 2 .38 The Copy Settings Wizard To use the Copy Settings Wizard, follow these steps: 1. Close SolidWorks. 2. Click Start ➪ Programs ➪ SolidWorks 2009 ➪ SolidWorks 2009 Tools ... and Outside option are illustrated in Figure 3. 16. FIGURE 3. 16 Using the Trim Away Inside and Outside options 84 SolidWorks Basics Part I FIGURE 3. 5 The Rectangle flyout...
Ngày tải lên : 11/08/2014, 18:20
  • 80
  • 142
  • 0
Wiley SolidWorks 2009 Bible Part 4 doc

Wiley SolidWorks 2009 Bible Part 4 doc

... Extrude-Boss1 or Extrude-Cut1. The “Base” part of the Extruded Boss/Base is a holdover from when SolidWorks did not allow mul- tibody parts, and the first feature in a part had special significance that ... and spline continuous curvature 216 Building Intelligence into Your Parts Part II FIGURE 7.6 Creating features with Instant 3D Notice the boss extrude symbol next to the hand in...
Ngày tải lên : 11/08/2014, 18:20
  • 80
  • 148
  • 0
Wiley SolidWorks 2009 Bible Part 5 pot

Wiley SolidWorks 2009 Bible Part 5 pot

... composed of numbers and mathematical operators. An expression such as 2 .37 5+(4.8 /3) -1.1 33 6 Building Intelligence into Your Parts Part II BEST PRACTICE BEST PRACTICE Although you can change the preferred ... Dynamic Mirror centerline with hatch marks 33 2 Building Intelligence into Your Parts Part II ON the CD-ROM ON the CD-ROM The CD-ROM contains a part called Chapter 10 Con...
Ngày tải lên : 11/08/2014, 18:20
  • 80
  • 206
  • 0
Wiley SolidWorks 2009 Bible Part 6 ppt

Wiley SolidWorks 2009 Bible Part 6 ppt

... Options, and press Ctrl+Q. The fillets should now fail. 32 . Click Undo to return the feature order to the way it was. 33 . Save the part. 37 3 Editing and Evaluation 11 FIGURE 11.6 Comparing the ... Fit Spline, as shown in Figure 11. 23. Do not exit the sketch. FIGURE 11. 23 Sketch3 in its new location 13. One of the goals of these edits is to smooth out the part. Remember that th...
Ngày tải lên : 11/08/2014, 18:20
  • 80
  • 155
  • 0
Wiley SolidWorks 2009 Bible Part 7 potx

Wiley SolidWorks 2009 Bible Part 7 potx

... can control the transparency of the parts not being edited. Figure 16 .3 shows this setting. FIGURE 16 .3 Part transparency for in-context control In-context part color transparency control 491 Component ... those parts, and will cause problems with any in-context features. If you suppress the “ground” part or any part that connects groups of parts, keep in mind that this can cau...
Ngày tải lên : 11/08/2014, 18:20
  • 80
  • 193
  • 0
Wiley SolidWorks 2009 Bible Part 8 ppt

Wiley SolidWorks 2009 Bible Part 8 ppt

... Data \SolidWorks\ SolidWorks 2009\ Design Library \. You should store them in another location, not in the SolidWorks installation directory, but in an area that you have selected to maintain SolidWorks ... Libraries Part IV FIGURE 17 .33 The bolt is too short. TIP TIP Remember that the pre-selection of a flat face is important so that you can use a 2D placement sketch, rather tha...
Ngày tải lên : 11/08/2014, 18:20
  • 80
  • 296
  • 0
Wiley SolidWorks 2009 Bible Part 9 pot

Wiley SolidWorks 2009 Bible Part 9 pot

... underlying template. However, you can change all of the settings, which is for the most part equivalent. SolidWorks 2009 offers custom drafting standards, which fulfills much of the function that the ... projection. Third angle is part of the ANSI standard used in the United States, while first angle is part of the ISO standard used in Europe. 654 Creating Drawings Part V FIGURE...
Ngày tải lên : 11/08/2014, 18:20
  • 80
  • 126
  • 0