Wiley SolidWorks 2009 Bible Part 2 doc

... Figure 2. 38. FIGURE 2. 38 The Copy Settings Wizard To use the Copy Settings Wizard, follow these steps: 1. Close SolidWorks. 2. Click Start ➪ Programs ➪ SolidWorks 20 09 ➪ SolidWorks 20 09 Tools ... 3.14 The Power Trim feature in action 47 Navigating the SolidWorks Interface 2 FIGURE 2. 19 The Welcome to SolidWorks screen FIGURE 2. 20 The Options tab of the Customi...

Ngày tải lên: 11/08/2014, 18:20

... with part and assembly models but not drawings. 158 SolidWorks Basics Part I FIGURE 5 .2 Scrollbars and splitters Using the Magnifying Glass A new visualization aid introduced in SolidWorks 20 09 ... be grayed out if any SolidWorks docu- ments are open (so you must close all SolidWorks documents to change it). When you zoom in such that the part/ assembly/drawing is partia...

Ngày tải lên: 11/08/2014, 18:20

... you close the sketch. This only works for 2D sketches; 3D sketches can be opened, but not closed this way. 24 4 Building Intelligence into Your Parts Part II Tangent propagation By default, fillets ... off of the part or until the feature fails. FIGURE 7. 32 Turning off the Tangent Propagation option 22 5 Selecting Features 7 FIGURE 7. 12 A loft with and without guide curves Middle...

Ngày tải lên: 11/08/2014, 18:20

... shallow pyramid shape. Open the part from the material on the CD-ROM for Chapter 29 called Chapter 29 – Cross Break.SLDPRT to exam- ine how this part was made. Figure 29 .27 shows the Cross Break tool ... the Cross Break tool applied to a sheet metal part. FIGURE 29 .27 The Cross Break tool applied to a part 898 Working with Specialized Functionality Part VII FIGURE 31.8 Lo...

Ngày tải lên: 11/08/2014, 18:20

... end constraint, 22 2 direction of, 22 2 Direction Vector end constraint, 22 3 end constraints, 22 2 22 3 entities used in, 22 0 example of, 21 9 guide curves, 22 4 isoparameter U-V lines, 22 4 making closed ... fillets applying values for, 25 1 25 2 best practices for, 25 0 guidelines for use of, 25 2 smooth transitions, 25 2 25 3 straight transitions, 25 2 25 3 zero radius value...

Ngày tải lên: 11/08/2014, 17:22

... 25 8 Constant width fillet 26 0 Full round fillet 26 0 Setback fillet 26 1 Selecting a Specialty Feature 26 4 Dome and Shape 26 4 Wrap feature 26 7 Scribe 26 8 Emboss 26 8 Deboss 26 8 Flex 27 0 Deform 27 3 Point ... Reference Points 23 8 Composite curve 23 8 Split lines 23 9 Equation Driven Curve 24 0 Filleting 24 0 Creating a constant radius fillet 24 2 Selecting entities t...

Ngày tải lên: 11/08/2014, 18:20

... called Chapter8 Tutorial2.sldprt. 2. Open a sketch on the side of the part, as shown in Figure 8 .26 . The straight line on top is 1.00 inch long, and the angled line ends 2. 70 inches from the edge, ... Figure 8 .27 . 4. Create a linear pattern using the rib, making it go 2 inches into the part. 5. Create a chamfer on the same side of the part as the original rib, as shown in Fi...

Ngày tải lên: 11/08/2014, 18:20

... extremely useful method for looking at mates. 3 92 Building Intelligence into Your Parts Part II FIGURE 11 .26 The results up to Step 26 FIGURE 11 .27 Fillets that should have failed 31. Go to ... the part itself. Starting with SolidWorks 20 09, features created in the assembly can be propagated to reside in the affected parts. Component patterns Component patterns can pa...

Ngày tải lên: 11/08/2014, 18:20

... those parts, and will cause problems with any in-context features. If you suppress the “ground” part or any part that connects groups of parts, keep in mind that this can cause other parts to ... relations to size parts when you are also using configurations to size parts. A non-configured part driven by a configured part only causes confusion. 500 Working with Assemblies Part III...

Ngày tải lên: 11/08/2014, 18:20

... folders are found at C:\Documents and Settings\All Users\ Application Data \SolidWorks\ SolidWorks 20 09\ Design Library \. You should store them in another location, not in the SolidWorks installation ... interface 554 Creating and Using Libraries Part IV FIGURE 17 .21 The User Settings page FIGURE 17 .22 The Define user settings page 545 Using Hole Wizard and Toolbox 17 Separate...

Ngày tải lên: 11/08/2014, 18:20