Wiley SolidWorks 2009 Bible Part 1 pdf

... installing 10 10 New installation or upgrade? 10 10 Level to install 10 10 Installation folders 10 11 Serial number and license server 10 11 SolidWorks Search 10 11 Performance feedback 10 11 Other software 10 11 Administrative ... software 10 11 Administrative Image 10 12 Configuration and Standardization 10 12 Data Management 10 12 Filenames 10 13 Rules of file manageme...

Ngày tải lên: 11/08/2014, 18:20

... is about 60%. 10 32 Appendixes Part VIII n Area Hatch/Fill: This setting determines the default hatch, scale, and angle for newly created hatch fills. Default is ANSI 31, scale :1, angle:0. Colors You ... perfor- mance, particularly on large assembly views. The alternative is to only show the rectangu- lar view border when dragging. Default is on. 10 36 Appendixes Part VIII FIGURE B...

Ngày tải lên: 11/08/2014, 18:20

... performing, 10 18 10 20 System Options Advanced, 10 64 Assemblies, 10 47 10 48 Backup/Recover, 10 57 Collaboration, 10 62 10 63 Colors, 10 32 10 34 Default Templates, 10 50 10 51 Display/Selection, 10 39 10 43 Drawings ... 345–346 using, 514 installation of SolidWorks Administrative Image, 10 12 from discs, 10 10 installation folders, 10 11 Installation Manager, 10 09 10 10 p...

Ngày tải lên: 11/08/2014, 17:22

... Wizard To use the Copy Settings Wizard, follow these steps: 1. Close SolidWorks. 2. Click Start ➪ Programs ➪ SolidWorks 2009 ➪ SolidWorks 2009 Tools ➪ Copy Settings Wizard. 3. Select Save Settings, ... Inside and Outside option are illustrated in Figure 3 .16 . FIGURE 3 .16 Using the Trim Away Inside and Outside options 84 SolidWorks Basics Part I FIGURE 3.5 The Rectang...

Ngày tải lên: 11/08/2014, 18:20

... default setting. Figure 5 .19 shows a sample part with all three settings. 17 6 SolidWorks Basics Part I FIGURE 5.20 The Color and Optics interface elements 13 8 SolidWorks Basics Part I NOTE NOTE Using ... over one of the splitters. 14 2 SolidWorks Basics Part I 1. From the CD-ROM, open the part named Chapter5Frame.sldprt. With the part open, click the Make Assembl...

Ngày tải lên: 11/08/2014, 18:20

... are simply Extrude1 where they used to be Extrude-Boss1 or Extrude-Cut1. The “Base” part of the Extruded Boss/Base is a holdover from when SolidWorks did not allow mul- tibody parts, and the first ... outer shape. Figure 7 .16 shows all these elements and the finished feature. FIGURE 7 .16 A sweep with two guide curves ON the CD-ROM ON the CD-ROM The part shown in Figure 7 .16 i...

Ngày tải lên: 11/08/2014, 18:20

... example, switch (x>2, 1. 5, x> ;1, .5 x< ;1, 2.5) reads as follows: “if x is greater than 2, then the answer is 1. 5; if x is not greater than 2 but greater than 1, then the answer is .5; ... configurations and design tables Working with Part Configurations 302 Building Intelligence into Your Parts Part II FIGURE 8 .18 Using a sketch-driven pattern FIGURE 8 .19 Using the...

Ngày tải lên: 11/08/2014, 18:20

... 12 .14 An example of what can occur when you do not enter proper descriptions for parts 388 Building Intelligence into Your Parts Part II FIGURE 11 . 21 Preparing for the Fit Spline FIGURE 11 .22 Creating ... Your Parts Part II Load You can apply loads to faces as force or pressure. You can also select multiple faces. Figure 11 .15 shows loads that are applied on the sample par...

Ngày tải lên: 11/08/2014, 18:20

... of the parts not being edited. Figure 16 .3 shows this setting. FIGURE 16 .3 Part transparency for in-context control In-context part color transparency control 4 91 Component Patterns 15 Dissolve ... references by using the Split Part command as well as the Insert Part (base or derived part) or the mirrored part functions. Figure 16 .6 shows the expanded FeatureManager fo...

Ngày tải lên: 11/08/2014, 18:20

... interface 554 Creating and Using Libraries Part IV FIGURE 17 . 21 The User Settings page FIGURE 17 .22 The Define user settings page 545 Using Hole Wizard and Toolbox 17 Separate parts are better for: n Keeping ... types. Available thread types are shown in Figure 17 .20. 573 Working with Library Features 18 FIGURE 18 .1 The Task pane docked to right side of the SolidWorks...

Ngày tải lên: 11/08/2014, 18:20