Welding Materials Handbook Part 5 pot

... be in the above ranges.) USES: This wire is recommended for welding 50 56 ,50 83, 50 86 ,51 54, and 53 56 aluminum alloys. USE THIS WIRE FOR WELDING ALUMINUM LANDING MATS. PROCEDURES: Wire and joint to ... POSITIONS Material Thickness (in.) .037 . 050 .062 .1 25 .187 Travel Amps volts Speed (ipm) 70 17 20-40 85 18 20 -50 100 18 25- 35 150 20 15- 25 150 20 10-20 (NOTE: The abov...

Ngày tải lên: 11/08/2014, 18:20

... . . . . . . . . 2-42 2-43 2-46 2-46 2-47 2-47 2-48 2-48 2-49 2-49 2 -50 2 -50 2 -51 2 -52 2 -53 2 -53 2 -54 2 -54 2 -55 2 -55 2 -56 2 -57 xiii CONTENTS (Continued) ATOMIZED METAL REPAIR COMPOUND (M-42) . ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 -58 2 -58 2 -59 2-60 2-60 2-61 2-63 2-64 2- 65 2-66 2-67 2-67 2-67 2-67 2-71 2-72 2-72 2-72 2-7...

Ngày tải lên: 11/08/2014, 18:20

... initialized by one trigger pulse 0 .50 0 .55 0.60 -12 -10 -8 -6 -4 -2 0 2 4 6 8 Time / μ s Voltage / kV b -1 .5 -1.0 -0 .5 0.0 0 .5 1.0 Current / A 0 .5 1.0 1 .5 2.0 2 .5 3.0 3 .5 4.0 -12 -10 -8 -6 -4 -2 0 2 4 6 8 Time ... electrode Parameters Mouse (d = 1 mm) Mouse (d = 0 .5 mm) Glass (d = 1 mm) Al-spike (d = 1 .5 mm) τ (ns) 25 ± 5 25 ± 5 6.0 ± 1 .5 23 ± 1 No...

Ngày tải lên: 21/06/2014, 01:20

... 59 1.3.3.4 Matrix 59 1.3.3 .5 Intermediate forms characterization 59 1.3.3 .5. 1 Metallized fibers 59 1.3.3 .5. 2 Monotapes 59 1.3.3 .5. 3 Lamina other than monotapes 59 1.3.3 .5. 4 Specialized forms 59 1.3.3.6 ... sampling 50 1.3.2.4 Specimen preparation 50 1.3.2 .5 Data documentation 55 1.3.3 MATERIALS PEDIGREE 58 1.3.3.1 Reinforcement 59 1.3.3.2 Reinforcement si...

Ngày tải lên: 10/08/2014, 11:21

... (Pa) 9.806 650 E+00 kip (1000 lbf) newton (N) 4.448 222 E+03 ksi (kip/in. 2 ) MPa 6.894 757 E+00 ksi√in. megapascal √meter 1.0989 (MPa#m 1/2)*** lbf-in. N-m 1.129 848 E-01 lbf-ft N-m 1. 355 818 E+00 lbf/in. 2 ... larger critical value, then the hypothesis is rejected. In both cases, the critical value chosen depends on the desired risk (often 0. 05) of rejecting the hypothesis when it is tru...

Ngày tải lên: 10/08/2014, 11:21

... condition Tensile 5 3 15 Fatigue 5 3 15 Creep 5 3 15 Crack Growth 5 3 15 Hardness 5 3 15 Microstructure (with magnification) 5 3 15 Chemical Analysis 5 3 15 Coefficient of Thermal Expansion 5 3 15 Density 5 ... Thermal Expansion (a) 5 1 15 min. per dir. Specific Heat (b) 5 1 5 Thermal Conductivity (a) 5 1 15 Electrical Conductivity (a) 5 1 15 Density (c)...

Ngày tải lên: 10/08/2014, 11:21

... ASTM Test Method D 355 2/D 355 2M, “Tensile Properties of Fiber-Reinforced Metal Matrix Composites,” Annual Book of ASTM Standards, Vol 15. 03, American Society for Testing and Materials, West Conshohocken, ... Standards, Vol 15. 03, American Society for Testing and Materials, 19 95, pp. 131-147. 1.4.2.3 ASTM Standard D5379/D5379M, "Standard Test Method for Shear Properties of Composit...

Ngày tải lên: 10/08/2014, 11:21

... invariant. In ternary systems (C = 3), invariants are reactions with four participating phases; whereas in a reaction with three participating phases, the compo - sitions vary in the course of the ... lattice points of neighboring lattices, in contrast to coherent or partially coherent interfaces. incoherent precipitate/particle Second phase precipitate whose interface with the matrix ....

Ngày tải lên: 10/08/2014, 11:22

... RNCB RNMCB-2, 12, 13, 14, 15, 16, 17, 18,20,21, 22,23,24, 25, 26,27,28 Additional copies may be obtained from: Commanding Officer (Code 157 1) NCBC, Port Hueneme, California 93043 -50 00 Naval Publications ... CBU-401,402,404,407,408,419(2ea) 39E PHIBCBONE/PHIBCBTTVO (4 ea) FT20 NAVCONSTRACEN Gulfport, PorHue ( 150 ea) 39F COM20THNCR DEPLOYED SUPPORT DIV FT78 NAVEDTRAPRODEVCEN (Code 3 152 ) G...

Ngày tải lên: 11/08/2014, 18:20

Ngày tải lên: 11/08/2014, 18:20