Modern Plastics Handbook 2011 Part 16 pdf

... 71. 18. Moore, S., Plastics Recycling Profit Soars in India,” Modern Plastics, June 1995, pp. 19–21. 19. Higgs, R., “New Technology to Boost European Recycling,” Plastics News, June 16, 1997, p. 56. 20. ... Is Putting Recyclate in Vacuums,” Modern Plastics, January 1997, p. 22. 120. Mapleston, P., “Housing May Be Built from Scrap in Low-Pressure Process,” Modern Plastics, Septem...

Ngày tải lên: 11/08/2014, 16:22

... reject finished parts. Whatever the source, economics dictate that the scrap be reintroduced into the material stream. The first step in the process is to grind the parts into a particle size small ... single desiccant-coated honeycomb wheel rotates slowly, exposing part of the wheel to process air, part to regen- eration, and part to cooling prior to returning to the process. 7.48 Chap...

Ngày tải lên: 11/08/2014, 16:22

... which includes Modern Plastics magazine and Modern Plastics World Encyclopedia. The Modern Plastics Handbook offers a thorough and comprehensive technical coverage of all aspects of plastics materials and ... the Modern Plastics team, namely, Robert D. Leaversuch, Executive Editor of Modern Plastics magazine, Stephanie Finn, Modern Plastics Events Manager, Steven J...

Ngày tải lên: 11/08/2014, 16:22

... Engineering Plastics, ” in Engineering Plastics, vol. 2, Engineering Materials Handbook, ASM International, Metals Park, Ohio, 1988, p. 69. 415. Berins, Plastics Engineering Handbook, pp. 48–49. 416. ... “Polyarylate,” in Modern Plastics Encyclopedia Handbook, McGraw-Hill, New York, 1994, p. 15. 147. Berins, Plastics Engineering Handbook, p. 66. 148. Dunkle, “Polyarylate,” p....

Ngày tải lên: 11/08/2014, 16:22

... Elastomers,” in Handbook of Plastics, Elastomers, and Composites, 3d ed., Charles A. Harper, ed., McGraw-Hill, New York, 1996. 10a. Joseph F. Meier, “Fundamentals of Plastics and Elastomers,” in Handbook ... Handbook of Plastics, Elastomers, and Composites, 3d ed., Charles A. Harper, ed., McGraw-Hill, New York, 1996. 10b. Leonard S. Buchoff, “Liquid and Low-Pressure Resin Systems,”...

Ngày tải lên: 11/08/2014, 16:22

... two-roll mills, and extruders. Polymer modifications, such as annealing molded parts and radiation of plastics parts, change the amount of orientation, crystallinity, and/or cross-linking in ... affected. With some difficult-to-crystal- lize thermoplastics, such as partially aromatic polyamides or PET, nucleants are needed to obtain useful parts with reasonable cycle times and mold temperat...

Ngày tải lên: 11/08/2014, 16:22

... faster cycles. Two- stage screw-plunger machines are generally employed for fast cycles, large parts, and parts with long flow lengths. In single-stage recipro- cating-screw injection units (Fig. ... units operate like extruders. Solid resin parti- cles are fed from the hopper, through the feed throat, and onto a rotating screw. Although plastic particles may be metered onto the plasticating...

Ngày tải lên: 11/08/2014, 16:22

... area of the molded part or parts at the mold parting surfaces. Overall cycles depend on molding material, part thickness, and mold temperature, and may be about 1 min for parts of 3-mm thickness ... Strong, A. B., Plastics, p. 295. 115. Ibid., pp. 296–297. 116. Petrothene® Polyolefins, p. 84. 117. Berins, M. L., Plastics Engineering Handbook, p. 117. 118. Wire and Cable Coaters’ Han...

Ngày tải lên: 11/08/2014, 16:22

... position is at the end of the part. Most of the part has a high confidence of fill. However regions far from the gate are shown in yellow, while areas at the end of the part are shown in red. Such ... shell-based analysis. These parts are also amenable to 3D/FEA. In addition to broadening the range of parts that can be simulated, 3D/FEA also couples well with solid modeling. A particular...

Ngày tải lên: 11/08/2014, 16:22

... the piece part cost will be greater for a part produced by structural foam molding than for a similar part made by injection molding. The reduced molding pressure does permit larg- er parts to ... the part will fail below its design limit. This requires careful attention to a number of critical areas. The majority of differences between the design of plastic parts and the design of pa...

Ngày tải lên: 11/08/2014, 16:22