Mechanical Engineer''''''''s Reference Book 2011 Part 5 pot
Mechanical Engineer''''s Reference Book 2011 Part 5 pot
... 40 40 50 50 65 65 80 80 100 100 120 EO 140 140 160 160 180 180 200 200 2 25 228 280 250 280 280 3 15 3 15 355 355 400 IM) 450 450 50 0 Grade 50 0 56 0 56 0 630 ... sizes i 35 1wI 1 350 680 400 .ux) 450 150 0 760 440 450 50 1 650 840 4811 Grade 6 to I6 N E +I - 52 0 290 ~ 1 45 ~ 38 0 250 0 3 150 - - ~ -26...
Ngày tải lên: 11/08/2014, 15:20
Mechanical Engineer''''s Reference Book 2011 Part 1 potx
... motion in three Further reading 1/ 35 1.3 .5 Balancing 1/23 1.6 Principles of thermodynamics 1/ 35 1.3.6 Balancing of rotating masses 1/23 1.6.1 Introduction 1/ 35 1.4 Vibrations 119 1.6.3 ... notch: $' = 2.36C,H2' (1.63) V = 2. 953 Cd(B - 0.2H) el5 - id)'I (1. 65) or neglecting the approach velocity: V = 2. 953 C,j(B - 0.2H)H" (1.66) For a...
Ngày tải lên: 11/08/2014, 15:20
Mechanical Engineer''''s Reference Book 2011 Part 4 pot
... 1l00100 110010, 1 loo! 10 I700III 110r000 1~0100' 11010:o 153 154 155 156 I57 I60 161 162 163 16d 1 65 I66 I67 I70 97, I72 - ~ coo1 I I! 00l0000 0010001 0010010 ... inventory file, for example, would contain information on each part stored in a warehouse. For each part would be held such data as the part number, description, quantity in sto...
Ngày tải lên: 11/08/2014, 15:20
Mechanical Engineer''''s Reference Book 2011 Part 8 potx
... - 0 1Cr 0.5Mo - 0 2.25Cr 1Mo - 0.5Cr 0.5Mo 0.25V -I - 1 - - - o/!* /- - &yo - 0 - %, @. - - &s5ec - n- - 1 I 1.0, I I i I 1 Figure 8 .53 Development ... and torsional wave speeds Table 8.1 CL Ws) cT Mild steel 51 50 3230 Aluminium 50 9C 3110 Glass 53 00 3260 Epoxy resin 154 0 950 Cast iron 3960 2470 8.1.8 Orthotropic material An...
Ngày tải lên: 11/08/2014, 15:20
Mechanical Engineer''''s Reference Book 2011 Part 13 pot
... compression cycle 151 1 15 to sound 15/ 140 15. 5.2 Pressure-enthalpy chart 151 1 15 15. 9.8 Noise indices 151 140 15. 5.3 Gas refrigeration cycle 151 1 15 15. 9.9 Noise-rating curves 15/ 141 15. 9.10 Community ... analysis 151 143 15. 7.2 Predictive preventive maintenance 151 124 15. 9.20 Noise control 15/ 143 15. 7.3 Condition monitoring 151 1 25 15. 9.21 Noise nuisa...
Ngày tải lên: 11/08/2014, 15:20
Mechanical Engineer''''s Reference Book 2011 Part 2 doc
... in use is the NE 555 . which is CK D Figure 2.116 D-type flip-flop manufactured as an 8-pin DIL package. The CMOS equiva- lent to the TTL-based NE 555 is the ICM 755 5. These packages ... packages are essentially identical, and ICM 755 5 can be used to replace NE 555 , although the converse is not always applicable. The so-called 55 5’ timer is very versatile and ca...
Ngày tải lên: 11/08/2014, 15:20
Mechanical Engineer''''s Reference Book 2011 Part 3 ppsx
... Thermal conductivity Ionization 1 05- 102 10 A Simple, robust io5-10 5 B Good general-purpose lo5-lo2 5- 10 A Simple, direct reading 1 05- 10-3 5- 10 C Wide range. Used for 103-10-2 ... Platinum - 13% rhodium/ platinum G 150 0 4 .5 mV at 50 0°C S Platinum - 10% rhodium/ rhodium CL 150 0 4.2 mV at 50 0°C T Copper/constantan - 250 -400 4.3 mV at 100°C...
Ngày tải lên: 11/08/2014, 15:20
Mechanical Engineer''''s Reference Book 2011 Part 6 pps
... AI-2.5Li 1.3Cu 0.8Mg O.IZr AI-2.3Li 2.7Cu 0.12Zr 1099. 1199 1060 EC 1200 2014 2024 2618 in50 - - 3103 31 05 30431 454 3 4047 4032 50 05 50 52 51 54 A 50 56A 54 54 50 53 6063 ... Wrought (BS 1470- 75) Notes Group 1 LM5-M 1060, 1 050 , 1200 LM10-TB in industrial atmospheres LM6M, LM9-TE and TF 3103, 31 05 LM18-M, LM20-M 50 05, 52 51, 51 54, 54 54 cea...
Ngày tải lên: 11/08/2014, 15:20
Mechanical Engineer''''s Reference Book 2011 Part 7 ppt
... 120 100- 150 1 75- 290 100 150 -2 05 130-190 150 -3 15 180 2 05 0.16-0.3 0.32-0.88 0.29-0.42 0 .56 -1.6 30 45 8-20 20 -50 15- 17 109-10** 2 x io9 100-160 56 -160 110-120 70-120 5- 13 5- 7.1 6-9 ... Hardness - .* 10-44 12-20 17-24 250 - 450 200-300 250 -330 410 -55 0 350 -480 350 -700 1, 650 630-670 1.3-2.1 2.2 No break SDa 50 -55 SD' 60- 75 SDa...
Ngày tải lên: 11/08/2014, 15:20