Manufacturing Handbook of Best Practices 2011 Part 15 docx
Manufacturing Handbook of Best Practices 2011 Part 15 docx
... 342 The Manufacturing Handbook of Best Practices
FIGURE 15. 8C Viscosity vs. itself, five samples apart.
FIGURE 15. 8D Viscosity vs. itself, ten samples apart.
FIGURE 15. 9 Autocorrelation ... 337
Non-normal distribution:
(15. 15)
C
pk
. A measure of both process dispersion and its centering about the average.
(15. 16)
where
(15. 17)
(15. 18)
Normal distributions:
(15. 19)...
Manufacturing Handbook of Best Practices 2011 Part 13 docx
... LLC
292
The Manufacturing Handbook of Best Practices
arrays, based on the design of experiments theory, to study a large number of decision
variables with a small number of experiments. ...
286
The Manufacturing Handbook of Best Practices
13.1 THE SIGNIFICANCE OF ROBUST DESIGN
Many studies have been performed demonstrating that the early design phase of...
Manufacturing Handbook of Best Practices 2011 Part 2 potx
... by CRC Press LLC
32
The Manufacturing Handbook of Best Practices
this publication, continuous improvement well might be less a matter of domination
and more one of survival.
Later, we will ... bring profound improvements to an organization. However, it is not
easy. It demands profound changes of an organization: first, on the part of its leaders,
and eventually, on the...
Manufacturing Handbook of Best Practices 2011 Part 3 pdf
... or all of the potential interactions (the formal term for this
SL3003Ch03Frame Page 54 Tuesday, November 6, 2001 6:11 PM
© 2002 by CRC Press LLC
66 The Manufacturing Handbook of Best Practices
PROCESS ... 2001 6:11 PM
© 2002 by CRC Press LLC
62 The Manufacturing Handbook of Best Practices
• Select factors and interactions to be tested
• Select number of factor levels...
Manufacturing Handbook of Best Practices 2011 Part 4 pptx
... scorecard — parts worksheet.
Part Number TDU
Name Scan Drive Yield
Period of Data 4/1/00 - Sigma
Total Part Count 1
Avg Defects /Part 0.1649
COQ
Avg Yield /Part 84.8%
Part Cost
Avg. Part Sigma 1.03
Variance
Supplier ... 2002 by CRC Press LLC
72
The Manufacturing Handbook of Best Practices
4.1.4 U
SE
OF
C
OMMON
M
ATERIALS
The fifth design considera...
Manufacturing Handbook of Best Practices 2011 Part 5 ppt
...
88
The Manufacturing Handbook of Best Practices
With IPPD, each process is still needed. It’s the sequencing, the sharing of
knowledge, and the elimination of hand-offs that now offer a product ... The Manufacturing Handbook of Best Practices
• Does the analysis follow accepted statistical protocol (such as confirma-
tion of a normal distribution)?
• Are the resul...
Manufacturing Handbook of Best Practices 2011 Part 6 ppsx
... LLC
110
The Manufacturing Handbook of Best Practices
the next process. The systematic identification and management of the various
processes employed within an organization, particularly the ... CRC Press LLC
118 The Manufacturing Handbook of Best Practices
• Requirements for approval of product, procedures, processes, and equipment
• Requirements for qualification...
Manufacturing Handbook of Best Practices 2011 Part 8 pptx
... 1:52 PM
© 2002 by CRC Press LLC
176
The Manufacturing Handbook of Best Practices
and lead to the loss of future business. Some of the causes of this waste may be
weak process control, poor ... 2002 by CRC Press LLC
172
The Manufacturing Handbook of Best Practices
These are shown in the basic lean manufacturing model (Figure 8.7). In addition,
lean manufa...
Manufacturing Handbook of Best Practices 2011 Part 10 doc
... Press LLC
228
The Manufacturing Handbook of Best Practices
•
Process Map. A two-dimensional version of a process flow chart that also
portrays handoffs and receipts of products or services ... total
number of handoffs that are a part of this process, recognizing that every time there
is a handoff, there is a strong potential for an error, an oversight, something left...
Manufacturing Handbook of Best Practices 2011 Part 12 potx
... be the
remaining 15% of value. But the number of parts or stock keeping units (SKUs)
represented by the A items, while being 70% or so of value, will be only about 15%
of your part matrix. The ...
The Manufacturing Handbook of Best Practices
assume you have 10,500 stockroom parts. Table 12.1 compares cycle counting
with physical inventory and shows the relative workloa...
Từ khóa: