Manufacturing Handbook of Best Practices 2011 Part 13 docx

... 286 The Manufacturing Handbook of Best Practices 13. 1 THE SIGNIFICANCE OF ROBUST DESIGN Many studies have been performed demonstrating that the early design phase of a product or ... designed. SL3003Ch13Frame Page 285 Tuesday, November 6, 2001 6:04 PM © 2002 by CRC Press LLC 292 The Manufacturing Handbook of Best Practices arrays, based on the design of...

Ngày tải lên: 11/08/2014, 14:20

... 342 The Manufacturing Handbook of Best Practices FIGURE 15.8C Viscosity vs. itself, five samples apart. FIGURE 15.8D Viscosity vs. itself, ten samples apart. FIGURE 15.9 Autocorrelation ... November 6, 2001 6:02 PM © 2002 by CRC Press LLC 334 The Manufacturing Handbook of Best Practices number of times, then on average a subgroup of size n = 3 will detect a 1 sigma shif...

Ngày tải lên: 11/08/2014, 14:20

... by CRC Press LLC 32 The Manufacturing Handbook of Best Practices this publication, continuous improvement well might be less a matter of domination and more one of survival. Later, we will ... bring profound improvements to an organization. However, it is not easy. It demands profound changes of an organization: first, on the part of its leaders, and eventually, on the...

Ngày tải lên: 11/08/2014, 13:22

... or all of the potential interactions (the formal term for this SL3003Ch03Frame Page 54 Tuesday, November 6, 2001 6:11 PM © 2002 by CRC Press LLC 66 The Manufacturing Handbook of Best Practices PROCESS ... 2001 6:11 PM © 2002 by CRC Press LLC 62 The Manufacturing Handbook of Best Practices • Select factors and interactions to be tested • Select number of factor levels...

Ngày tải lên: 11/08/2014, 13:22

... scorecard — parts worksheet. Part Number TDU Name Scan Drive Yield Period of Data 4/1/00 - Sigma Total Part Count 1 Avg Defects /Part 0.1649 COQ Avg Yield /Part 84.8% Part Cost Avg. Part Sigma 1.03 Variance Supplier ... 2002 by CRC Press LLC 72 The Manufacturing Handbook of Best Practices 4.1.4 U SE OF C OMMON M ATERIALS The fifth design considera...

Ngày tải lên: 11/08/2014, 13:22

... 88 The Manufacturing Handbook of Best Practices With IPPD, each process is still needed. It’s the sequencing, the sharing of knowledge, and the elimination of hand-offs that now offer a product ... The Manufacturing Handbook of Best Practices • Does the analysis follow accepted statistical protocol (such as confirma- tion of a normal distribution)? • Are the resul...

Ngày tải lên: 11/08/2014, 13:22

... LLC 110 The Manufacturing Handbook of Best Practices the next process. The systematic identification and management of the various processes employed within an organization, particularly the ... CRC Press LLC 118 The Manufacturing Handbook of Best Practices • Requirements for approval of product, procedures, processes, and equipment • Requirements for qualification...

Ngày tải lên: 11/08/2014, 13:22

... 1:52 PM © 2002 by CRC Press LLC 176 The Manufacturing Handbook of Best Practices and lead to the loss of future business. Some of the causes of this waste may be weak process control, poor ... 2002 by CRC Press LLC 172 The Manufacturing Handbook of Best Practices These are shown in the basic lean manufacturing model (Figure 8.7). In addition, lean manufa...

Ngày tải lên: 11/08/2014, 14:20

... Press LLC 228 The Manufacturing Handbook of Best Practices • Process Map. A two-dimensional version of a process flow chart that also portrays handoffs and receipts of products or services ... total number of handoffs that are a part of this process, recognizing that every time there is a handoff, there is a strong potential for an error, an oversight, something left...

Ngày tải lên: 11/08/2014, 14:20

... The Manufacturing Handbook of Best Practices assume you have 10,500 stockroom parts. Table 12.1 compares cycle counting with physical inventory and shows the relative workload of each method of ... availability of parts SL3003Ch12Frame Page 263 Tuesday, November 6, 2001 6:05 PM © 2002 by CRC Press LLC 266 The Manufacturing Handbook of Best Practices shipping...

Ngày tải lên: 11/08/2014, 14:20