Manufacturing Handbook of Best Practices 2011 Part 10 doc

... 1:52 PM © 2002 by CRC Press LLC 238 The Manufacturing Handbook of Best Practices 10. 4.4 P HASE 1 — M ODEL F This model (Figure 10. 7) is best understood by beginning its examination ... SL3003Ch10Frame Page 240 Friday, November 9, 2001 1:52 PM © 2002 by CRC Press LLC 234 The Manufacturing Handbook of Best Practices FIGURE 10. 2 Objective: redu...

Ngày tải lên: 11/08/2014, 14:20

... LLC 292 The Manufacturing Handbook of Best Practices arrays, based on the design of experiments theory, to study a large number of decision variables with a small number of experiments. ... 286 The Manufacturing Handbook of Best Practices 13.1 THE SIGNIFICANCE OF ROBUST DESIGN Many studies have been performed demonstrating that the early design phase of...

Ngày tải lên: 11/08/2014, 14:20

... 342 The Manufacturing Handbook of Best Practices FIGURE 15.8C Viscosity vs. itself, five samples apart. FIGURE 15.8D Viscosity vs. itself, ten samples apart. FIGURE 15.9 Autocorrelation ... November 6, 2001 6:02 PM © 2002 by CRC Press LLC 334 The Manufacturing Handbook of Best Practices number of times, then on average a subgroup of size n = 3 will detect a 1 sigma shif...

Ngày tải lên: 11/08/2014, 14:20

... by CRC Press LLC 32 The Manufacturing Handbook of Best Practices this publication, continuous improvement well might be less a matter of domination and more one of survival. Later, we will ... bring profound improvements to an organization. However, it is not easy. It demands profound changes of an organization: first, on the part of its leaders, and eventually, on the...

Ngày tải lên: 11/08/2014, 13:22

... curing a material at ~100 °C. If your oven maintains temperature ± 5°C, then an experiment of 95, 100 , 105 °C may be a waste of time. At the same time, an experiment of 50, 100 , 150°C may be ... 2001 6:11 PM © 2002 by CRC Press LLC 62 The Manufacturing Handbook of Best Practices • Select factors and interactions to be tested • Select number of factor levels Ⅲ Two...

Ngày tải lên: 11/08/2014, 13:22

... 6, 2001 6 :10 PM © 2002 by CRC Press LLC 72 The Manufacturing Handbook of Best Practices 4.1.4 U SE OF C OMMON M ATERIALS The fifth design consideration is use of the materials ... SL3003Ch04Frame Page 73 Tuesday, November 6, 2001 6 :10 PM © 2002 by CRC Press LLC 74 The Manufacturing Handbook of Best Practices start with some of the comm...

Ngày tải lên: 11/08/2014, 13:22

... seasoned? SL3003Ch05Frame Page 95 Tuesday, November 6, 2001 6 :10 PM © 2002 by CRC Press LLC 100 The Manufacturing Handbook of Best Practices 5.7 METHODOLOGIES OF SIMULTANEOUS PRODUCT AND PROCESS DEVELOPMENT After ... — and the rest of the organization — must accept this. SL3003Ch05Frame Page 94 Tuesday, November 6, 2001 6 :10 PM © 2002 by CRC Press LLC 102 The Manufacturi...

Ngày tải lên: 11/08/2014, 13:22

... Press LLC 110 The Manufacturing Handbook of Best Practices the next process. The systematic identification and management of the various processes employed within an organization, particularly ... CRC Press LLC 118 The Manufacturing Handbook of Best Practices • Requirements for approval of product, procedures, processes, and equipment • Requirements for qualificati...

Ngày tải lên: 11/08/2014, 13:22

... 1:52 PM © 2002 by CRC Press LLC 176 The Manufacturing Handbook of Best Practices and lead to the loss of future business. Some of the causes of this waste may be weak process control, poor ... 2002 by CRC Press LLC 172 The Manufacturing Handbook of Best Practices These are shown in the basic lean manufacturing model (Figure 8.7). In addition, lean manufa...

Ngày tải lên: 11/08/2014, 14:20

... The Manufacturing Handbook of Best Practices assume you have 10, 500 stockroom parts. Table 12.1 compares cycle counting with physical inventory and shows the relative workload of each method of ... availability of parts SL3003Ch12Frame Page 263 Tuesday, November 6, 2001 6:05 PM © 2002 by CRC Press LLC 266 The Manufacturing Handbook of Best Practices shippi...

Ngày tải lên: 11/08/2014, 14:20