Manual Gearbox Design Part 3 pps

... x-x- 36 x 1760 TW Tdriven where RR = rolling radius road wheel (in) Tp = no. of teeth - pinion 34 Manual Gearbox Design companies means that the gear and transmission designers ... that the lubrication system must be part of the early planning in the initial stages of the gearbox design and designed to cater for the particular gearbox application, the loads...

Ngày tải lên: 11/08/2014, 13:22

... losses due to oil churning, often caused by poor casing design, especially surfaces during the motion of meshing 36 Manual Gearbox Design Principles of gear lubrication In considering ... the bulk oil temperature is maintained below 80°C, this combination will satisfy 38 Manual Gearbox Design produce than single helicals, they are widely used where quiet and smooth-r...

Ngày tải lên: 11/08/2014, 13:22

... 2.1C2.65 2 .35 -3 .OO 3. W3.75 2.10-2.65 3. 354.25 2.65 -3. 35 2 .35 -3. 00 3 .W3.75 3. 754.75 2.65 -3. 35 3. 354.25 4.25-5 .30 3. W3.75 3. 754.75 4.75-6.00 3. 35-4.25 5.3W.70 3. 754.75 4.75-6.60 ... 2.5 3. 0 2.1 1.15 1. 93 2 .3 2.7 3. 1 3. 5 1.6 2.2 2.8 3. 4 2 .3 1.25 2.14 1.9 2.2 2.5 2.8 1 .3 1.9 2.5 1.8 1.05 1.70 2 .3 2.7 3. 1 3. 5 1.6 2.2 2.8 3. 4...

Ngày tải lên: 11/08/2014, 13:22

... by Signor Valerio Colotti in the Formula One gearbox he designed in about 1960. The author has used this particular system in numerous gearbox designs with very few minor snags. The Colotti-type ... and Plug. Gearbox design - rear-engined racing cars 1 43 view, thereby providing a positive checking facility as the two gears are rolled together. 3 With this arrangement,...

Ngày tải lên: 11/08/2014, 13:22

... I-90 2.65 0.00 4 .34 1.69 SR 30 3 SR 3 to SR 30 4 0.00B 0.00 8. 73 8.89 SR 30 4 SR 16 to Bremerton Ferry 0.00 0.00 3. 51 3. 24 SR 30 5 SR 3 to Winslow Ferry 0.02 0.00 13. 52 13. 50 SR 30 7 SR 30 5 to SR 104 ... 5.25 SR 31 0 SR 3 to SR 30 4 0.00 0.00 1.84 1.84 US 39 5 Congressional High Priority Route 13. 05 13. 05 270.26 275.09 SR 401 SR 101 to SR 4 0.00 0.00 12. 13 12. 13...

Ngày tải lên: 10/08/2014, 20:20

... evaluations. Comprehensive design reviews are included at different phases of the engineering design process, such as conceptual design, preliminary or schematic design, and final d etail design. In most ... the design of large industrial processes that consist of many systems that give rise to design complexity and consequent high risk of design in- tegrity. These industrial pro...

Ngày tải lên: 02/07/2014, 10:20

... method Gearbox casing Materials guide 38 38 39 39 40 46 50 52 53 54 61 66 66 67 67 80 82 83 84 88 96 100 106 1 13 1 13 1 13 117 1 30 134 134 135 137 137 139 141 ... years’ involvement in the design of Formula One racing gearboxes. Manual Gearbox Design Alec Stokes Society of Automotive Engineers P= EINEMANN 2 Manual Ge...

Ngày tải lên: 11/08/2014, 13:22

... Manual Gearbox Design (e) Equiv. twisting moment due to combined twisting and bending: nd3 - x4 16 3 Angle of torsional deflection (in degrees) - solid circular section - 5 83. 6 ... clearance required and the necessary clearances between the engine, gearbox and other surrounding components. 8 Manual Gearbox Design K, =load distribution factor: pinion overhu...

Ngày tải lên: 11/08/2014, 13:22

... transmission casing design and material in any particular transmission design. The transmission unit consists of four main components or units: 1 The gears and shafts. 2 The bearings. 3 The lubrication ... 64 Manual Gearbox Design such gears the tooth-bearing area moves toward the toe of the tooth, but on the ... gears, great differences in sliding motion arise over variou...

Ngày tải lên: 11/08/2014, 13:22

... follows: 716N n1 M,=- 82 Manual Gearbox Design Table 55 Pressure angle a = 229, Z, I, i 5 3 2'6 7 8 9 10 11 12 13 14 15 16 18 20 22 24 26 28 30 35 40 45 50 1.00 1.00 ... than 2.5 -3 : 1. The gear hobs for tooth profile 1 can be used for cutting both the pinion and crown wheel. 90 Manual Gearbox Design Fiepn S7 (cont.) Crown wheel...

Ngày tải lên: 11/08/2014, 13:22