MACHINERY''''''''S HANDBOOK 27th ED Part 20 ppsx
MACHINERY''''S HANDBOOK 27th ED Part 20 ppsx
... standardized, is mentioned on Handbook page 2363 together with suggested toler- ances. Keys Proportioned According to Transmitted Torque.—As previously stated, if key sizes are based on shaft ... constants 0.2887 and 0.1293 referred to in a preceding paragraph are derived and deduce a general rule Guide to Machinery's Handbook 27th Edition Copyright 200 4, Industrial Press, Inc.,...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 3 ppsx
... 85,000 1 3 ⁄ 4 5200 48,400 95,800 9000 84,000 163,000 7400 68,600 124,000 5200 48,400 95,800 1 7 ⁄ 8 … 55 ,200 ……95,800 ……78 ,200 ……55 ,200 … 2 6200 63 ,200 … 10,800 109,600 … 8800 89,600 … 6200 63 ,200 … 2 1 ⁄ 8 7200 ... longer manufactured in the United States. 120 1060 3240 204 1835 5640 170 1500 4540 120 1060 3240 5 ⁄ 16 a 200 1655 … 346 2865 … 282 2340 … 200 1655 … 3 ⁄ 8 270 238...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 19 ppsx
... not exceed 200 degrees F. Where worm speed exceeds 3600 revolutions per minute, or 200 0 feet per minute rubbing speed, a force feed lubrica- tion may be required. Auxiliary cooling by forced air, ... MCCAULEY, EDITOR RICCARDO HEALD, ASSOCIATE EDITOR MUHAMMED IQBAL HUSSAIN, ASSOCIATE EDITOR 200 4 I NDUSTRIAL PRESS INC. N EW YORK Guide to Machinery's Handbook 27th Edition Copyright...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 1 doc
... 7293 9337P3P113P73PP 95535535535535 97P113PP37P313P3 993PP3P73PP311P Machinery's Handbook 27th Edition Copyright 200 4, Industrial Press, Inc., New York, NY ix The editors would like to acknowledge all those who contributed ideas, suggestions, and criticisms ... E. Green, as editor emeritus, contributed much useful, well organized mate- rial to this edition. He also provided invalua...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 2 pptx
... 19.90 20. 00 20. 11 20. 21 20. 32 20. 42 20. 52 20. 63 20. 73 20. 84 200 20. 94 21.05 21.15 21.26 21.36 21.47 21.57 21.68 21.78 21.89 210 21.99 22.10 22 .20 22.30 22.41 22.51 22.62 22.72 22.83 22.93 220 23.04 ... the table Critical Speed Formulas. Formulas for Single Concentrated Load Bearings supported Bearings supported Bearings fixed Bearings fixed One-fixed — One supported...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 4 pps
... be supplied in one of the following conditions and surface finishes: Conditions: Hot-rolled or forged (natural); hot-rolled or forged and annealed; hot-rolled or forged and heat-treated; cold- ... and annealed. Finishes: Hot-rolled finish (scale not removed); pickled or blast-cleaned; cold-drawn; turned or machined; rough ground; centerless ground or precision flat ground; and pol- ished (rou...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 5 pot
... 0.000 120 Max 120. 220 119. 820 0. 620 120. 087 119.880 0.294 120. 054 119.964 0.125 120. 035 119.988 0.069 120. 035 120. 000 0.057 Min 120. 000 119.600 0.180 120. 000 119.793 0. 120 120. 000 119.929 0.036 120. 000 ... 0.000 200 Max 200 .290 199.760 0. 820 200.115 199.830 0.400 200 .072 199.950 0.168 200 .046 199.985 0.090 200 .046 200 .000 0.075 Min 200 .000 199.470 0.240 200...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 7 pptx
... y19 +0.11966 y19 +0.19804 y19 +0.26602 x20 +0.46194 x20 +0.49114 x20 +0.50000 x20 +0.49240 x20 +0.47194 y20 −0.19134 y20 −0.09369 y20 0.00000 y20 +0.08682 y20 +0.16514 x21 +0.39668 x21 +0.45241 ... { 175–225 90 70 f s 17 370 8 490 36 150 17 200 17 595 8 815 28 410 13 590 15 1460 8 2170 7 625 3 790 225–300 (Low-carbon alloy): 1 320, 2315, 2 320, 4110, 4 120, 4 320, 8 020, 8 620 { 150 200 9...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 8 pptx
... FA70-G12VP Machinery's Handbook 27th Edition Copyright 200 4, Industrial Press, Inc., New York, NY 1174 GRINDING FEEDS AND SPEEDS User Calibration of Recommendations It is recommended to copy or redraw the ... grinding which may be described as through-feed, in-feed, and end-feed methods. Through-feed Method of Grinding.—The through-feed method is applied to straight cylindrical par...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 9 pptx
... Fig. 24. Hemmed “S” Slip This is the modified “S” slip, by adding hem and an angle for reinforcing. The hem edge is a flat, and finished edge. Hemmed “S” slip is mostly applied with angle. ... be made for the cut-out part to be supported when it is freed from the workpiece so that it does not pinch and break the wire. EDM applied to grinding machines is termed EDG. The process uses a ......
Ngày tải lên: 11/08/2014, 10:23