MACHINERY''''''''S HANDBOOK 27th ED Part 14 ppt
MACHINERY''''S HANDBOOK 27th ED Part 14 ppt
... straight-sided splines. BS 2059 was prepared on the hole basis, the hole being the constant member, and provide for different fits to be obtained by varying the size of the splined or serrated shaft. Part ... diagram described. The calculations are shown in detail so that if equations are programmed for a digital computer, the results can be verified easily. Obviously, the intermediate poin...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 2 pptx
... 12.88 12.98 13.09 13.19 13.30 13.40 13.51 130 13.61 13.72 13.82 13.93 14. 03 14. 14 14. 24 14. 35 14. 45 14. 56 140 14. 66 14. 76 14. 87 14. 97 15.08 15.18 15.29 15.39 15.50 15.60 150 15.71 15.81 15.92 16.02 ... the table Critical Speed Formulas. Formulas for Single Concentrated Load Bearings supported Bearings supported Bearings fixed Bearings fixed One-fixed — One supported One...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 7 pptx
... 0.95482 y13 0.9 8146 x14 0.98091 x14 1.00000 x14 0.98470 x14 0.94550 x14 0.89092 x14 0.82743 x14 0.75979 y14 0.36317 y14 0.50000 y14 0.62274 y14 0.72700 y14 0.81174 y14 0.87787 y14 0.92721 x15 ... −0.16 514 y13 +0.49572 y13 +0.50000 y13 +0.49635 y13 +0.48652 y13 +0.47194 x14 +0.19134 x14 +0.12434 x14 +0.06027 x14 0.00000 x14 −0.05598 y14 +0.46194 y14 +0.48429 y14 +0.49635 y14 +0.50000 y14 ....
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 8 pptx
... grinding which may be described as through-feed, in-feed, and end-feed methods. Through-feed Method of Grinding.—The through-feed method is applied to straight cylindrical parts. The work is given ... from the edge, dressing the edge to a slight radius, or swivel- ing the regulating wheel a bit. Scored work is caused by burrs, abrasive grains, or removed material being imbedded in or fused to...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 9 pptx
... Fig. 24. Hemmed “S” Slip This is the modified “S” slip, by adding hem and an angle for reinforcing. The hem edge is a flat, and finished edge. Hemmed “S” slip is mostly applied with angle. ... be made for the cut-out part to be supported when it is freed from the workpiece so that it does not pinch and break the wire. EDM applied to grinding machines is termed EDG. The process uses a ......
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 12 pptx
... ANSI B1.11–1958 (R2001) is based on the withdrawn ASA Truncated Whitworth standard, dimensional nomenclature is described below. Machinery's Handbook 27th Edition Copyright 2004, Industrial ... Handbook 27th Edition Copyright 2004, Industrial Press, Inc., New York, NY 1894 MEASURING SCREW THREADS eter may be determined. The cone-shaped point of the measuring screw is slightly rou...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 1 doc
... inches=== Volume V 3 .141 6hR 2 r 2 –()0.7854hD 2 d 2 –()== = 3 .141 6ht 2Rt–()3 .141 6ht D t–()== 3 .141 6ht 2rt+()3 .141 6ht d t+()== 3 .141 6ht R r+()1.5708ht D d+()== V 3 .141 6ht D t–()3 .141 6 28× 436 4–()× 3 .141 6 28× ... E. Green, as editor emeritus, contributed much useful, well organized mate- rial to this edition. He also provided invaluable practical guidance to the editorial sta...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 3 ppsx
... occur. Diameter Reduction: The inside diameter reduces during deflection. This reduction should be computed and proper clearance provided over the supporting rod. Also, allow- ances should be considered for ... customarily furnished. Regular lay rope has less tendency to spin or untwist when placed under load and is generally selected where long ropes are employed and the loads handled are fr...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 4 pps
... hardness ………1800–1900 5143 0 430 … 140 0–1500 c …… …… 5143 0F d …… 1250 140 0 c …… …… 5143 1 431 … 1150–1225 b … 1800–1950 Oil or air To desired hardness 5143 4 … } … 140 0–1600 c …… …… 5143 6 … 5144 0A d 440A d } … 1350 144 0 b 1550–1650 ... F) Quenching Medium Temper 5140 9 …… … 1625 … Air … 5141 0 410 … 1300–1350 b b Usually air cooled but may be furnace cooled. 1500–1650 … } O...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 5 pot
... Fit b Machinery's Handbook 27th Edition Copyright 2004, Industrial Press, Inc., New York, NY PREFERRED NUMBERS 689 Preferred Numbers Preferred numbers are series of numbers selected to be used for standardization ... 1.30 814 11 0.71171 0.79797 0.88399 0.96974 1.05520 1 .140 34 1.22513 1.30954 12 0.71 314 0.79941 0.88542 0.97117 1.05662 1 .141 75 1.22654 1.31095 13 0. 7145 8 0.80...
Ngày tải lên: 11/08/2014, 10:23