MACHINERY''''''''S HANDBOOK 27th ED Part 13 pps
MACHINERY''''S HANDBOOK 27th ED Part 13 pps
... ……………… 129 39 13/ 39 65 24 ……72 24 44 130 39 12/39 60 ……………… 131 20 6/20 58 40 ……28 44 … 132 33 10/33 59 ……………… 133 21 6/21 56 24 ……48 44 … 134 21 6/21 56 28 ……48 44 … 135 27 8/27 58 ……………… 136 17 5/17 ... Engineers) www.sme.org Machinery's Handbook 27th Edition Copyright 2004, Industrial Press, Inc., New York, NY 2020 MILLING MACHINE INDEXING 137 D 137 40 173 F 173 40 218...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 3 ppsx
... 140 139 138 137 136 135 Torque, pound-inch 38.90 50.60 58.44 64.30 81.68 96.45 101.5 124.6 146.0 158.3 199.0 213. 3 301.5 410.6 542.5 700.0 Inside Diameter, inch Deflection, degrees per coil 13 ⁄ 16 0.8125 ... customarily furnished. Regular lay rope has less tendency to spin or untwist when placed under load and is generally selected where long ropes are employed and the loads handled...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 4 pps
... be supplied in one of the following conditions and surface finishes: Conditions: Hot-rolled or forged (natural); hot-rolled or forged and annealed; hot-rolled or forged and heat-treated; cold- ... and annealed. Finishes: Hot-rolled finish (scale not removed); pickled or blast-cleaned; cold-drawn; turned or machined; rough ground; centerless ground or precision flat ground; and pol- ished (rou...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 10 pps
... 0.312 Machinery's Handbook 27th Edition Copyright 2004, Industrial Press, Inc., New York, NY BOLTS AND NUTS 1 513 An externally threaded fastener that must be assembled with a nut to perform its intended service ... and bolts are furnished with a natural (as processed) finish, unplated or uncoated unless otherwise specified. Alloy steel socket head cap screws are furnished with an o...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 11 pps
... 12.500 13. 154 0.562 13. 063 0.209 293740 352390 2. 813 3.001 0.225 2.980 0.103 32870 16845 12.750 13. 417 0.562 13. 324 0.209 299610 366460 2.834 3.027 0.225 3.006 0.103 33120 17595 13. 000 13. 680 ... UP C F Machinery's Handbook 27th Edition Copyright 2004, Industrial Press, Inc., New York, NY COTTER AND CLEVIS PINS 1667 PINS AND STUDS Dowel-Pins.—Dowel-pins are used either...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 18 pps
... 0.0007262 137 7 137 8 1898884 2616662152 37.12142 11.12798 0.0007257 137 8 137 9 1901641 2622362939 37 .134 89 11 .130 67 0.0007252 137 9 138 0 1904400 2628072000 37.14835 11 .133 36 0.0007246 138 0 138 1 1907161 ... 0.0007386 135 4 135 5 1836025 2487 8138 75 36.81032 11.06572 0.0007380 135 5 135 6 1838736 2493326016 36.82391 11.06844 0.0007375 135 6 135 7 1841449 2498846293 36....
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 19 ppsx
... that is composed of 4 parts of sulphur diox- ide to 96 parts of distilled water. The specimens are immersed in this, face upward, and removed as soon as the polished surface is frosted. This takes ... not exceed 200 degrees F. Where worm speed exceeds 3600 revolutions per minute, or 2000 feet per minute rubbing speed, a force feed lubrica- tion may be required. Auxiliary cooling by forced air...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 20 ppsx
... standardized, is mentioned on Handbook page 2363 together with suggested toler- ances. Keys Proportioned According to Transmitted Torque.—As previously stated, if key sizes are based on shaft ... referred to in a preceding paragraph are derived and deduce a general rule Guide to Machinery's Handbook 27th Edition Copyright 2004, Industrial Press, Inc., New York, NY 108 SECTION 13...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 1 doc
... 3 45355355355355 47P 3 PP 323833 7133 P 49783313P 3 P 7 3 P 113 5131 7 4135 3P 3 P 1131 3P 5379317P 3 7 1131 947341 55553553553553 57343 1131 7133 P P 3 719 59 113 719317P 3477 311 61P73PP313P311P3 63 3 P P 3 P P ... Value 132 Capitalized Cost 133 Equivalent Uniform Annual Cost 134 Rate of Return 134 Benefit-cost Ratio 134 Payback Period 134 Break-even Analysis 137 Overhead Expenses...
Ngày tải lên: 11/08/2014, 10:23
MACHINERY''''S HANDBOOK 27th ED Part 2 pptx
... 12.98 13. 09 13. 19 13. 30 13. 40 13. 51 130 13. 61 13. 72 13. 82 13. 93 14.03 14.14 14.24 14.35 14.45 14.56 140 14.66 14.76 14.87 14.97 15.08 15.18 15.29 15.39 15.50 15.60 150 15.71 15.81 15.92 16.02 16 .13 ... the table Critical Speed Formulas. Formulas for Single Concentrated Load Bearings supported Bearings supported Bearings fixed Bearings fixed One-fixed — One supported One...
Ngày tải lên: 11/08/2014, 10:23