Machinery Component Maintenance and Repair Part 17 pdf

Ngày tải lên: 11/08/2014, 10:23

... in setting heavy machinery and in repairing concrete foundations. Specifi- cations for Portland cement grouting and epoxy grouting of rotating equip- 62 Machinery Component Maintenance and Repair Among ... and a good knowledge of principles and practices of 34 Machinery Component Maintenance and Repair 32 Machinery Component Maintenance and Repair Figur...

Ngày tải lên: 11/08/2014, 10:23

... relaxation, creep, hydrostatic end pressure, and residual gasket loads. 166 Machinery Component Maintenance and Repair 158 Machinery Component Maintenance and Repair Table 4-1 Torque Tables for Spiral ... should be removed and left out only when the inlet line is free of welding beads, pipe scale, and other extraneous matter. 188 Machinery Component Maintenance...

Ngày tải lên: 11/08/2014, 10:23

... the reinforcing steel cage is fabricated and installed. Typically, 78 Machinery Component Maintenance and Repair 82 Machinery Component Maintenance and Repair Figure 3-5. Foundation after regrouting. ... surface with a chip- ping gun, sandblasting the surface after the concrete has cured, and rough- 88 Machinery Component Maintenance and Repair Figure 3-12. M...

Ngày tải lên: 11/08/2014, 10:23

... to the form board, and forming a proper seal. Care should be taken to 144 Machinery Component Maintenance and Repair Machinery Foundations and Grouting 135 Chapter 4 Process Machinery Piping* Fundamentals ... set 146 Machinery Component Maintenance and Repair Machinery Foundations and Grouting 137 II. Specification of Pregrouted Baseplates 1. The underside of t...

Ngày tải lên: 11/08/2014, 10:23

... fixture and the dial Machinery Alignment 213 Figure 5-11. Optalign ® laser-optic alignment system. 192 Machinery Component Maintenance and Repair 190 Machinery Component Maintenance and Repair ... Face -and- rim has lower geometric accuracy than reverse-indicator, for spans exceeding coupling or jig diameter. 210 Machinery Component Maintenance and Repair one...

Ngày tải lên: 11/08/2014, 10:23

... ± È Î Í ˘ ˚ ˙ ++ Ê Ë ˆ ¯ ± 232 Machinery Component Maintenance and Repair * Courtesy of A-Line Mfg., Inc., Liberty Hill, Texas (Tel. 877-778-5454). 234 Machinery Component Maintenance and Repair Figure 5-25. ... with water and measuring volumes, the whole can be less than the sum of its parts. A parallel situation exists in (Text continued on page 245) 238 Machinery...

Ngày tải lên: 11/08/2014, 10:23

... circuit and instrument must be employed. The output from the phase reference sensor 280 Machinery Component Maintenance and Repair A light push fit between arbor and rotor will facilitate assembly and ... rotor. Maintenance and Production Balancing Machines Balancing machines may also be categorized by their application in the following three groups: 286 Machinery Compon...

Ngày tải lên: 11/08/2014, 10:23

... in plane A. U U d couple per £◊ 3 UU static per £ 3 326 Machinery Component Maintenance and Repair 344 Machinery Component Maintenance and Repair Figure 6-47. Field balancing worksheet. Listed ... within their respective URR limit circles to have the 318 Machinery Component Maintenance and Repair 328 Machinery Component Maintenance and Repair with suffic...

Ngày tải lên: 11/08/2014, 10:23

... interchangeability. 370 Machinery Component Maintenance and Repair Ball Bearing Maintenance and Replacement 373 Table 7-3 Ball Bearing Interchange Table 374 Machinery Component Maintenance and Repair Table ... adding material to, or removing it from, the rotor. 354 Machinery Component Maintenance and Repair Part III Maintenance and Repair of Machiner...

Ngày tải lên: 11/08/2014, 10:23