Machinery Component Maintenance and Repair Part 10 pptx

... interchangeability. 370 Machinery Component Maintenance and Repair Ball Bearing Maintenance and Replacement 373 Table 7-3 Ball Bearing Interchange Table 374 Machinery Component Maintenance and Repair Table ... adding material to, or removing it from, the rotor. 354 Machinery Component Maintenance and Repair Part III Maintenance and Repair of Machiner...

Ngày tải lên: 11/08/2014, 10:23

... in setting heavy machinery and in repairing concrete foundations. Specifi- cations for Portland cement grouting and epoxy grouting of rotating equip- 62 Machinery Component Maintenance and Repair Among ... and a good knowledge of principles and practices of 34 Machinery Component Maintenance and Repair 32 Machinery Component Maintenance and Repair Figur...

Ngày tải lên: 11/08/2014, 10:23

... the reinforcing steel cage is fabricated and installed. Typically, 78 Machinery Component Maintenance and Repair 82 Machinery Component Maintenance and Repair Figure 3-5. Foundation after regrouting. ... installed and injection is begun at the next location. This step-wise 100 Machinery Component Maintenance and Repair Figure 3-24. The foundation is dressed...

Ngày tải lên: 11/08/2014, 10:23

... to the form board, and forming a proper seal. Care should be taken to 144 Machinery Component Maintenance and Repair Machinery Foundations and Grouting 135 Chapter 4 Process Machinery Piping* Fundamentals ... set 146 Machinery Component Maintenance and Repair Machinery Foundations and Grouting 137 II. Specification of Pregrouted Baseplates 1. The underside of t...

Ngày tải lên: 11/08/2014, 10:23

... relaxation, creep, hydrostatic end pressure, and residual gasket loads. 166 Machinery Component Maintenance and Repair 158 Machinery Component Maintenance and Repair Table 4-1 Torque Tables for Spiral ... 490 33,060 22 ,102 10, 000 222 22 ,102 490 6 6.88 8.25 16.27 12 1.00 490 33,060 24,381 10, 000 201 24,381 490 8 8.88 10. 38 22.68 12 1.13 710 43,680 23,112 10, 00...

Ngày tải lên: 11/08/2014, 10:23

... fixture and the dial Machinery Alignment 213 Figure 5-11. Optalign ® laser-optic alignment system. 192 Machinery Component Maintenance and Repair 190 Machinery Component Maintenance and Repair ... Face -and- rim has lower geometric accuracy than reverse-indicator, for spans exceeding coupling or jig diameter. 210 Machinery Component Maintenance and Repair on...

Ngày tải lên: 11/08/2014, 10:23

... ± È Î Í ˘ ˚ ˙ ++ Ê Ë ˆ ¯ ± 232 Machinery Component Maintenance and Repair * Courtesy of A-Line Mfg., Inc., Liberty Hill, Texas (Tel. 877-778-5454). 234 Machinery Component Maintenance and Repair Figure 5-25. ... with water and measuring volumes, the whole can be less than the sum of its parts. A parallel situation exists in (Text continued on page 245) 238 Machinery...

Ngày tải lên: 11/08/2014, 10:23

... circuit and instrument must be employed. The output from the phase reference sensor 280 Machinery Component Maintenance and Repair A light push fit between arbor and rotor will facilitate assembly and ... rotor. Maintenance and Production Balancing Machines Balancing machines may also be categorized by their application in the following three groups: 286 Machinery Compon...

Ngày tải lên: 11/08/2014, 10:23

... limit circles to have the 318 Machinery Component Maintenance and Repair 328 Machinery Component Maintenance and Repair with sufficient accuracy (ideally within ± 10 percent of value), the U mar test ... in plane A. U U d couple per £◊ 3 UU static per £ 3 326 Machinery Component Maintenance and Repair 344 Machinery Component Maintenance and Repair Figu...

Ngày tải lên: 11/08/2014, 10:23

... resulting in poor operation and reduced life. These precautions apply to both bearing seats and shoulders. 398 Machinery Component Maintenance and Repair Figure 7-25. Burrs and nicks may interfere ... located. Using a dial type indicator, find the point and mark it with a crayon so 402 Machinery Component Maintenance and Repair Figure 7-28. A hand gauge may be used...

Ngày tải lên: 11/08/2014, 10:23