Machinery Component Maintenance and Repair Part 8 docx

... circuit and instrument must be employed. The output from the phase reference sensor 280 Machinery Component Maintenance and Repair A light push fit between arbor and rotor will facilitate assembly and ... positions of the correction planes and bearings. In a soft- 282 Machinery Component Maintenance and Repair Figure 6- 18. Influence of cross effects in rotors with...

Ngày tải lên: 11/08/2014, 10:23

... the reinforcing steel cage is fabricated and installed. Typically, 78 Machinery Component Maintenance and Repair 82 Machinery Component Maintenance and Repair Figure 3-5. Foundation after regrouting. ... surface with a chip- ping gun, sandblasting the surface after the concrete has cured, and rough- 88 Machinery Component Maintenance and Repair Figure 3-1...

Ngày tải lên: 11/08/2014, 10:23

... in setting heavy machinery and in repairing concrete foundations. Specifi- cations for Portland cement grouting and epoxy grouting of rotating equip- 62 Machinery Component Maintenance and Repair Among ... and a good knowledge of principles and practices of 34 Machinery Component Maintenance and Repair 32 Machinery Component Maintenance and Repair Figur...

Ngày tải lên: 11/08/2014, 10:23

... 6.22 2 68 68 26 4.25 7,514 283 544 0.47 6.47 280 80 26 4.25 8, 840 332 639 0.47 6.47 3 68 68 26 4.25 7,514 283 544 0.47 6.47 380 80 26 4.25 8, 840 332 639 0.47 6.47 3 98 98 26 4.25 10 ,82 9 407 783 0.47 ... 0.45 6.22 1 48 48 18 4.00 3,456 1 38 250 0.45 6.22 153 53 21 4.00 4,452 1 78 322 0.45 6.22 245 45 15 4.00 2,700 1 08 195 0.45 6.22 252 52 18 4.00 3,744 150 271 0.45 6.22...

Ngày tải lên: 11/08/2014, 10:23

... 5 .88 9.43 8 0 .88 320 25,140 21,329 10,000 150 21,329 320 5 5 .81 7.00 11.97 8 0 .88 320 25,140 16 ,80 7 10,000 190 16 .80 7 320 6 6 .88 8. 25 16.27 12 0 .88 320 25,140 18, 540 10,000 173 18, 540 320 8 8 .88 ... (inches) 3 3 / 8 4 1 / 2 2 1 / 4 3 3 / 8 4 1 / 2 2 1 / 4 3 3 / 4 4 1 / 2 2 5 / 8 3 3 / 4 4 1 / 2 2 5 / 8 4 5 / 8 4 5 / 8 3 1 / 4 4 5 / 8 4 5 / 8 3 1 / 4 4 7...

Ngày tải lên: 11/08/2014, 10:23

... fixture and the dial Machinery Alignment 213 Figure 5-11. Optalign ® laser-optic alignment system. 192 Machinery Component Maintenance and Repair 190 Machinery Component Maintenance and Repair ... parallel reading + () =+ + + 2 0 004 0 0 08 0 0 08 0 1 68 in Cin 216 Machinery Component Maintenance and Repair Figure 5-14. Sag compensator. Process Machin...

Ngày tải lên: 11/08/2014, 10:23

... ± È Î Í ˘ ˚ ˙ ++ Ê Ë ˆ ¯ ± 232 Machinery Component Maintenance and Repair * Courtesy of A-Line Mfg., Inc., Liberty Hill, Texas (Tel. 87 7-7 78- 5454). 234 Machinery Component Maintenance and Repair Figure 5-25. ... with water and measuring volumes, the whole can be less than the sum of its parts. A parallel situation exists in (Text continued on page 245) 2 38 Machin...

Ngày tải lên: 11/08/2014, 10:23

... within their respective URR limit circles to have the 3 18 Machinery Component Maintenance and Repair 3 28 Machinery Component Maintenance and Repair with sufficient accuracy (ideally within ± 10 percent ... in plane A. U U d couple per £◊ 3 UU static per £ 3 326 Machinery Component Maintenance and Repair 344 Machinery Component Maintenance and Repair...

Ngày tải lên: 11/08/2014, 10:23

... interchangeability. 370 Machinery Component Maintenance and Repair Ball Bearing Maintenance and Replacement 373 Table 7-3 Ball Bearing Interchange Table 374 Machinery Component Maintenance and Repair Table ... stators or tiebars. URR UU U U U = - =- 12 1 2 1 1 3 58 Machinery Component Maintenance and Repair 360 Machinery Component Maintenance and Re...

Ngày tải lên: 11/08/2014, 10:23

... resulting in poor operation and reduced life. These precautions apply to both bearing seats and shoulders. 3 98 Machinery Component Maintenance and Repair Figure 7-25. Burrs and nicks may interfere ... located. Using a dial type indicator, find the point and mark it with a crayon so 402 Machinery Component Maintenance and Repair Figure 7- 28. A hand gauge may be u...

Ngày tải lên: 11/08/2014, 10:23