Machinery Component Maintenance and Repair Part 6 pps
Machinery Component Maintenance and Repair Part 6 pps
... fixture and the dial
Machinery Alignment 213
Figure 5-11. Optalign
®
laser-optic alignment system.
192 Machinery Component Maintenance and Repair
190 Machinery Component Maintenance and Repair
... 0. 160 in.
Sag correction
orrected bottom parallel reading
+
()
=+ +
+
2 0 004 0 008 0 008
0 168
in
Cin
2 16 Machinery Component Maintenance and Repair
Figur...
Machinery Component Maintenance and Repair Part 4 pps
... 0.45 6. 22
264 64 22 4.00 5 ,63 2 225 407 0.45 6. 22
268 68 26 4.25 7,514 283 544 0.47 6. 47
280 80 26 4.25 8,840 332 63 9 0.47 6. 47
368 68 26 4.25 7,514 283 544 0.47 6. 47
380 80 26 4.25 8,840 332 63 9 ... set
1 46 Machinery Component Maintenance and Repair
Machinery Foundations and Grouting 137
II. Specification of Pregrouted Baseplates
1. The underside of th...
Machinery Component Maintenance and Repair Part 11 pps
... resulting in poor operation
and reduced life. These precautions apply to both bearing seats and
shoulders.
398 Machinery Component Maintenance and Repair
Figure 7-25. Burrs and nicks may interfere ... the shaft. This will help prevent burrs and
nicks which may interfere with the proper seating of the inner ring face
3 96 Machinery Component Maintenance and Repair...
Machinery Component Maintenance and Repair Part 15 pps
... control such as hot gas expander blades can be left as
5 56 Machinery Component Maintenance and Repair
574 Machinery Component Maintenance and Repair
1. Carburize only the areas to have a hardened ... of three ways:
Protecting Machinery Parts Against Loss of Surface 573
568 Machinery Component Maintenance and Repair
The constrast in wear ratios between the ca...
Machinery Component Maintenance and Repair Part 2 pdf
... in
setting heavy machinery and in repairing concrete foundations. Specifi-
cations for Portland cement grouting and epoxy grouting of rotating equip-
62 Machinery Component Maintenance and Repair
Among ... and a good knowledge of principles and practices of
34 Machinery Component Maintenance and Repair
32 Machinery Component Maintenance and Repair
Figu...
Machinery Component Maintenance and Repair Part 3 docx
... the reinforcing steel cage is fabricated and installed. Typically,
78 Machinery Component Maintenance and Repair
82 Machinery Component Maintenance and Repair
Figure 3-5. Foundation after regrouting. ... surface with a chip-
ping gun, sandblasting the surface after the concrete has cured, and rough-
88 Machinery Component Maintenance and Repair
Figure 3-12. M...
Machinery Component Maintenance and Repair Part 5 pdf
... 33, 060 55, 261 10,000
89 266
2
2.75 3.38 3.01 8 0.88
320 25,140 66 ,893 10,000
48 160
2.5 3.25 3.88 3.50 8
1.00 490 33, 060 75 ,62 0 10,000
65 245
3
3.75 4.75 6. 68 8 0.88
320 25,140 30,1 26 10,000
1 06 ... 1.38
1, 360 69 ,300 25,588 10,000 531
25,588 1, 360
18 18.50 20.75 69 .33 24
1.38 1, 360 69 ,300 23,991 10,000
567 23,991 1, 360
20 20.50 22.75 76. 39 24 1.50
1 ,60 0 84,300...
Machinery Component Maintenance and Repair Part 7 pot
... ±
È
Î
Í
˘
˚
˙
++
Ê
Ë
ˆ
¯
±
232 Machinery Component Maintenance and Repair
* Courtesy of A-Line Mfg., Inc., Liberty Hill, Texas (Tel. 877-778-5454).
234 Machinery Component Maintenance and Repair
Figure 5-25. ... Figure 6- 6, is that condition in which the central
principal axis of inertia is neither parallel to, nor intersects the shaft axis.
266 Machinery Component...
Machinery Component Maintenance and Repair Part 8 docx
... circuit and
instrument must be employed. The output from the phase reference sensor
280 Machinery Component Maintenance and Repair
A light push fit between arbor and rotor will facilitate assembly and ... rotor.
Maintenance and Production Balancing Machines
Balancing machines may also be categorized by their application in the
following three groups:
2 86 Machinery Comp...
Machinery Component Maintenance and Repair Part 9 potx
... A.
U
U
d
couple
per
£◊
3
UU
static per
£ 3
3 26 Machinery Component Maintenance and Repair
344 Machinery Component Maintenance and Repair
Figure 6- 47. Field balancing worksheet.
Listed in Table 6- 3 are residual unbalances ... within their respective URR limit circles to have the
318 Machinery Component Maintenance and Repair
328 Machinery Component Main...
Từ khóa: