Machinery Component Maintenance and Repair Part 5 pdf

... lb) 0 .5 0. 75 1. 25 0.79 4 0. 75 200 18,120 92,284 10,000 22 100 0. 75 1.00 1 .56 1.13 4 0. 75 200 18,120 64,024 10,000 31 100 1 1. 25 1.88 1 .53 4 0.88 320 25, 140 65, 555 10,000 49 160 1. 25 1 .56 2.38 2 .51 4 ... 18.69 20. 75 63.78 24 1. 25 1,000 55 ,740 20,9 75 10,000 477 20,9 75 1,000 20 20.69 22. 75 70. 25 24 1. 25 1,000 55 ,740 19,044 10,000 52 5 19,044 1,000 24 24....

Ngày tải lên: 11/08/2014, 10:23

... in setting heavy machinery and in repairing concrete foundations. Specifi- cations for Portland cement grouting and epoxy grouting of rotating equip- 62 Machinery Component Maintenance and Repair Among ... and a good knowledge of principles and practices of 34 Machinery Component Maintenance and Repair 32 Machinery Component Maintenance and Repair Figur...

Ngày tải lên: 11/08/2014, 10:23

Ngày tải lên: 11/08/2014, 10:23

... reinforcing steel cage is fabricated and installed. Typically, 78 Machinery Component Maintenance and Repair 82 Machinery Component Maintenance and Repair Figure 3 -5. Foundation after regrouting. ... operators important advantages of reduced downtime, lower labor costs, and less Machinery Foundations and Grouting 95 98 Machinery Component Maintenance and...

Ngày tải lên: 11/08/2014, 10:23

... 15 4.00 2,340 93 169 0. 45 6.22 148 48 18 4.00 3, 456 138 250 0. 45 6.22 153 53 21 4.00 4, 452 178 322 0. 45 6.22 2 45 45 15 4.00 2,700 108 1 95 0. 45 6.22 252 52 18 4.00 3,744 150 271 0. 45 6.22 258 58 ... 4,872 1 95 352 0. 45 6.22 264 64 22 4.00 5, 632 2 25 407 0. 45 6.22 268 68 26 4. 25 7 ,51 4 283 54 4 0.47 6.47 280 80 26 4. 25 8,840 332 639 0.47 6.47 368 68 26 4....

Ngày tải lên: 11/08/2014, 10:23

... fixture and the dial Machinery Alignment 213 Figure 5- 11. Optalign ® laser-optic alignment system. 192 Machinery Component Maintenance and Repair 190 Machinery Component Maintenance and Repair ... in Cin 216 Machinery Component Maintenance and Repair Figure 5- 14. Sag compensator. Process Machinery Piping 1 95 used quite readily to draw graphical plots...

Ngày tải lên: 11/08/2014, 10:23

... ± È Î Í ˘ ˚ ˙ ++ Ê Ë ˆ ¯ ± 232 Machinery Component Maintenance and Repair * Courtesy of A-Line Mfg., Inc., Liberty Hill, Texas (Tel. 877-778 -54 54). 234 Machinery Component Maintenance and Repair Figure 5- 25. Views ... water and measuring volumes, the whole can be less than the sum of its parts. A parallel situation exists in (Text continued on page 2 45) 238 Machi...

Ngày tải lên: 11/08/2014, 10:23

... circuit and instrument must be employed. The output from the phase reference sensor 280 Machinery Component Maintenance and Repair A light push fit between arbor and rotor will facilitate assembly and ... rotor. Maintenance and Production Balancing Machines Balancing machines may also be categorized by their application in the following three groups: 286 Machinery Compon...

Ngày tải lên: 11/08/2014, 10:23

... 8-hole rotors, a log with 45 test mass spacing must be used. m gin in g= ◊ = 5 4 1 25 . . . 10 10 0 5 05 U per plane gin gin mar () =◊ ◊ =◊ 316 Machinery Component Maintenance and Repair Figure 6-30. ... in plane A. U U d couple per £◊ 3 UU static per £ 3 326 Machinery Component Maintenance and Repair 344 Machinery Component Maintenance and Repair Figur...

Ngày tải lên: 11/08/2014, 10:23

... tiebars. URR UU U U U = - =- 12 1 2 1 1 358 Machinery Component Maintenance and Repair 360 Machinery Component Maintenance and Repair 6-B-2 Calibration (Master) Rotor (5. 35) : A rotor (usually the first of ... interchangeability. 370 Machinery Component Maintenance and Repair Ball Bearing Maintenance and Replacement 373 Table 7-3 Ball Bearing Interchange Tab...

Ngày tải lên: 11/08/2014, 10:23