Machinery Component Maintenance and Repair Part 4 pps

... 58 21 4. 00 4, 872 195 352 0 .45 6.22 2 64 64 22 4. 00 5,632 225 40 7 0 .45 6.22 268 68 26 4. 25 7,5 14 283 544 0 .47 6 .47 280 80 26 4. 25 8, 840 332 639 0 .47 6 .47 368 68 26 4. 25 7,5 14 283 544 0 .47 6 .47 380 ... (in) 139 39 15 4. 00 2, 340 93 169 0 .45 6.22 148 48 18 4. 00 3 ,45 6 138 250 0 .45 6.22 153 53 21 4. 00 4, 452 178 322 0 .45 6.22 245 45 15 4. 00 2,700 1...

Ngày tải lên: 11/08/2014, 10:23

... fixture and the dial Machinery Alignment 213 Figure 5-11. Optalign ® laser-optic alignment system. 192 Machinery Component Maintenance and Repair 190 Machinery Component Maintenance and Repair ... - = 0 0 14 9 4 0 029 2 0 0316 0 0 145 0 0171 say move IB 0.017in. north 228 Machinery Component Maintenance and Repair Appendix 4- C Detailed Checklist for Rota...

Ngày tải lên: 11/08/2014, 10:23

... shaft. 4. If mounted DF with the outer rings floating instead of DB, the bearing may be loose and have no preload. In addition, the balls 41 2 Machinery Component Maintenance and Repair Figure 7 -42 . ... 7 -46 , 7 -47 , and 7 -48 illustrate the effects of light, medium, and heavy preloads on bearings of each type. The top curve on each chart is Ball Bearing Maintenance an...

Ngày tải lên: 11/08/2014, 10:23

... control such as hot gas expander blades can be left as 556 Machinery Component Maintenance and Repair 5 74 Machinery Component Maintenance and Repair 1. Carburize only the areas to have a hardened ... 7 140 AMS 647 0E AMS 642 5 135 Type G N EZ Carbon 0.38–0 .43 0.21–0.26 0.30–0 .40 0.20–0.27 0.30–0 .40 Manganese 0.50–0.70 0.50–0.70 0 .40 –0.70 0 .40 –0.70 0.50–1.10 Sili...

Ngày tải lên: 11/08/2014, 10:23

... and a good knowledge of principles and practices of 34 Machinery Component Maintenance and Repair 32 Machinery Component Maintenance and Repair Figure 2-3. Simplified computer program used to ... in setting heavy machinery and in repairing concrete foundations. Specifi- cations for Portland cement grouting and epoxy grouting of rotating equip- 62 Machinery Co...

Ngày tải lên: 11/08/2014, 10:23

... the reinforcing steel cage is fabricated and installed. Typically, 78 Machinery Component Maintenance and Repair 82 Machinery Component Maintenance and Repair Figure 3-5. Foundation after regrouting. ... installed and injection is begun at the next location. This step-wise 100 Machinery Component Maintenance and Repair Figure 3- 24. The foundation is dressed...

Ngày tải lên: 11/08/2014, 10:23

... (inches) 3 3 / 8 4 1 / 2 2 1 / 4 3 3 / 8 4 1 / 2 2 1 / 4 3 3 / 4 4 1 / 2 2 5 / 8 3 3 / 4 4 1 / 2 2 5 / 8 4 5 / 8 4 5 / 8 3 1 / 4 4 5 / 8 4 5 / 8 3 1 / 4 4 7 / 8 4 5 / 8 3 1 / 2 4 7 / 8 4 5 / 8 3 1 / 2 5 1 / 4 4 5 / 8 3 7 / 8 5 1 / 4 4 5 / 8 3 7 / 8 6 1 / 8 4 3 / 4 4 1 / 2 6 1 / 8 4 3 / 4 4 1 / 2 6 1 / 2 8 5 / 8 56 1 / 2 8 5 / 8 5 7 1 / 2 8 3 / 4 5 7 /...

Ngày tải lên: 11/08/2014, 10:23

... ± È Î Í ˘ ˚ ˙ ++ Ê Ë ˆ ¯ ± 232 Machinery Component Maintenance and Repair * Courtesy of A-Line Mfg., Inc., Liberty Hill, Texas (Tel. 877-778- 545 4). 2 34 Machinery Component Maintenance and Repair Figure 5-25. ... by electric motors”: For liquids 200°F and below, set motor shaft at same height as pump shaft. 2 54 Machinery Component Maintenance and Repair Fi...

Ngày tải lên: 11/08/2014, 10:23

... circuit and instrument must be employed. The output from the phase reference sensor 280 Machinery Component Maintenance and Repair A light push fit between arbor and rotor will facilitate assembly and ... knife-edges, roller stands, and vertical pendu- lum types (Figure 6- 14) . All are capable of only detecting and/ or indicat- ing static unbalance. Balancing of Machinery...

Ngày tải lên: 11/08/2014, 10:23

... A. U U d couple per £◊ 3 UU static per £ 3 326 Machinery Component Maintenance and Repair 344 Machinery Component Maintenance and Repair Figure 6 -47 . Field balancing worksheet. Listed in Table ... within their respective URR limit circles to have the 318 Machinery Component Maintenance and Repair 328 Machinery Component Maintenance and Repair with suf...

Ngày tải lên: 11/08/2014, 10:23