Industrial Machinery Repair Part 4 docx

... 5,000 3,600 1,750 1,000 200 10 8,700 12,000 25,000 44 ,000 220,000 20 5,500 8,000 17,000 30,000 150,000 30 4, 000 6,000 13,000 24, 000 127,000 40 2,800 4, 500 11,000 20,000 111,000 50 3,500 9,300 18,000 ... supply, (3) corrosion, (4) material fatigue, and (5) use of unsuitable lubricants. Bearings 97 Figure 6.19 Spherical roller bearing assembly 239 230 240 231 241 222 232 213 223 45 33...

Ngày tải lên: 11/08/2014, 08:22

... especially true 210 Conveyors Table 10 .4 Factor A for self-lubricating bronze bearings Conveyor . 6 9 10 12 14 16 18 20 24 diameter, in Factor A 54 96 1 14 171 255 336 41 4 510 690 Slight variations can ... coffee beans, 0 .4; sawdust, 0.7; soda ash (light), 0.7; soybeans, 0.5; fly ash, 0 .4. Group 3 Includes materials with small lumps mixed with fines. Values of F are: alum, 1 .4; ashe...

Ngày tải lên: 11/08/2014, 08:22

... wet rags. 14 Oil returning to the sump is visually cloudy and foaming. You conclude that the oil is: A. Contaminated with soot. B. Contaminated with water. C. Contaminated with metal particles. D. ... Preventive/Predictive Maintenance 19 4 Calibration interval and when due; 5 Calibration procedures and necessary controls; 6 Actual values of latest calibration; 7 History of maintenance and...

Ngày tải lên: 05/08/2014, 11:20

... 2 (With seals) Sealing essential 4 Rubber bushes 4 4 Elastically stiff 111 Strip flexures 2 1 1 2 (Watch corrosion) 11 Rating: 1 - Excellent, 2 - Good,3-Fair ,4- Poor Source: Adapted by Integrated ... drives for engines of cars and trucks. G16 Parts of agricultural machinery; individual components of engines (gasoline or diesel) for cars and trucks. G6.3 Parts or process plant machines; m...

Ngày tải lên: 05/08/2014, 11:20

... transmit 210 Conveyors Table 10 .4 Factor A for self-lubricating bronze bearings Conveyor . 6 9 10 12 14 16 18 20 24 diameter, in Factor A 54 96 1 14 171 255 336 41 4 510 690 Slight variations can ... coffee beans, 0 .4; sawdust, 0.7; soda ash (light), 0.7; soybeans, 0.5; fly ash, 0 .4. Group 3 Includes materials with small lumps mixed with fines. Values of F are: alum, 1 .4; ashes (dry)...

Ngày tải lên: 05/08/2014, 11:20

... proper ISO particulate code 312 Gears and Gearboxes Figure 14. 35 Normal wear pattern Figure 14. 36 Wear pattern caused by abrasives in lubricating oil Abnormal Wear Figures 14. 36 through 14. 39 illustrate ... ratings Surface speed ft./min. Below 32 ◦ 32 ◦ –150 ◦ 150 ◦ –200 ◦ Below 150 42 65 150 150–300 42 65 120 300–750 42 50 65 Over 750 42 50 55 328 Lubrication the separators because t...

Ngày tải lên: 05/08/2014, 11:20

... Pumps 395 Chapter 22 Steam Traps 43 2 Chapter 23 V-Belt Drives 44 1 Chapter 24 Maintenance Welding 46 0 Appendix A 539 Index 541 8 Introduction: Why Use Best Maintenance Repair Practices? at times, ... Ricky. Industrial machinery repair : best maintenance practices pocket guide / Ricky Smith and Keith Mobley. p. cm. ISBN 0-7506-7621-3 (pbk : alk. paper) 1. Machinery Maintenance...

Ngày tải lên: 05/08/2014, 11:20

... horsepower 11 A “C” belt with a nominal length of 60 inches is 4 10 " long. What identification should be marked on the belt? A. C410 B. C60 /4 C. C 64 D. C56 12 When replacing one of a set of belts, the ... groove sheave. 44 Maintenance Skills Assessment 3 What should the fluid pass through before it reaches the pump? A. Prepump precipitator B. Metal diffuser C. Heat exchanger D. Str...

Ngày tải lên: 05/08/2014, 11:20

... speed, rpm Radial load, lb Speed limit 6 10,000 1000 100 10 100 1000 10,0002 346 2 346 346 4 3 2 8 6 4 3 2 8 6 4 3 2 8 6 4 3 2 Figure 6.7 Guide to selecting ball or roller bearings Ball Bearings Common ... 5,000 3,600 1,750 1,000 200 10 8,700 12,000 25,000 44 ,000 220,000 20 5,500 8,000 17,000 30,000 150,000 30 4, 000 6,000 13,000 24, 000 127,000 40 2,800 4, 500 11,000 20,000 111,...

Ngày tải lên: 05/08/2014, 11:20

... will run. See Figure 7.7. 24& quot; 1" 2" 3" 4& quot; 5" Figure 7.6 Tensioning Figure 7.7 Final alignment 1 24 Chain Drives they are an equal distance apart. Make sure that the ... supply, (3) corrosion, (4) material fatigue, and (5) use of unsuitable lubricants. 7 Chain Drives “Only Permanent Repairs Made Here” Introduction Chain drives are an important part of a con...

Ngày tải lên: 05/08/2014, 11:20