Illustrated Sourcebook of Mechanical Components Part 8 doc

... space. ILLUSTRATED SOURCE BOOK of MECHANICAL COMPONENTS SECTION 18 CAMS Generating Cam Curves 18- 2 Balance Grooved Cams 18- 9 Computer and N/C Simplifies Cam Design 18- 15 Theory of Envelopes: ... Cam Design Equations 18- 18 Cams and Gears Team Up in Programmed Motion 18- 28 Minimum Cam Size 18- 30 Spherical Cams: Linking Up Shafts 18- 38 Tailored Cycloid C...

Ngày tải lên: 11/08/2014, 08:22

... in., D2=5 .8 in., - =8. 56 L = 130in. Nc=2,375 rprn For Aluminum multiply uolues of N, byLOO26 , For Mognosium multipb vofues of Nc by 0. 987 9 \ . 4-26 m :D, / 8HC3 3. ... more projecting pins, the 3um of the radii of the pins being equal to the eccentricity of offset of the shafts. The lines of criiter between each pair of pins remain pa...

Ngày tải lên: 11/08/2014, 08:22

... length of connecting rod ILLUSTRATED SOURCEBOOK of MECHANICAL COMPONENTS SECTION 28 DESIGN Volume and CG Equations 28- 2 Common Area of Intersecting Circles 28- 10 Compound Angles 28- 12 ... 28- 12 Calculation of Dihedral Angles 28- 15 Frustums of Cones 28- 18 Length of Material for 90-Degree Bends 28- 19 8 Simple Methods to Measure Moment of Ine...

Ngày tải lên: 11/08/2014, 08:22

... 79.2432 79 .86 66 80 .3100 80 .9333 81 .3770 82 .0000 82 .4439 83 .0666 83 .5107 84 .1333 84 .5777 85 .2000 85 .6446 86 .2666 86 .7115 87 .3333 87 .7 784 88 .4000 88 .84 54 89 .4666 89 .9121 83 88 .5333 9 0.5 ... 78 79 74.6666 75.7333 76 .80 00 77 .86 66 . 78. 9333 80 .0000 81 .0666 82 .1333 83 .2000 84 .2666 ao 81 82 85 .3333 87 .4666 81 moo 76....

Ngày tải lên: 11/08/2014, 08:22

... method of attaching the ends of the belting to the device or product being positioned. 3-5 An example of a clamp groove profile which is used for attaching modified curvilinear tooth profile ... the result of the development and use of drop- forged, rivetless, Keystone chain. The dimensions of several sizes of Keystone chain links are shown below with two examples of...

Ngày tải lên: 11/08/2014, 08:22

... angle of a = 48 des. The shoe is pivoted at a distance h of 4 in. from the center. BY Eq (73 tall 8= p [(4)(5.25) (0 .80 902) -4(1 .88 496+0.95l0G)T _- 4 (1 .88 496-0.95106) ... and Eq (2), accurate values I of torque can be easily determined. ILLUSTRATED SOURCEBOOK of MECHANICAL COMPONENTS SECTION 9 Various Methods of Locking Threaded...

Ngày tải lên: 11/08/2014, 08:22

... Removal of the screw permits easy removal of the clampcd part. Heavy pressure toward the side of the key out of contact with the slot may permit slight movement due to the springing of the ... ?/' deg part ' ,I, I opprox:v oi+4 FIG. 1-When nut is tightened, the flange on the edge of the movable part is drawn against the machined edge of the stat...

Ngày tải lên: 11/08/2014, 08:22

... psi ONE-PARALLEL SERIES 26 1 .87 1.10 1.7 0.034 0. 085 0.4 0 .88 4 2.21 600 305,000 THREE-PARALLEL SERIES 48 1 .87 1.10 1.7 0.055 0.046 1.2 0 .88 4 2.21 600 266.000 0-Rings ... or J.I.C. 0-Rings and Gaskets 53 to 88 AN 6230 or J. I. C. gaskets 1 to 52 1 to7 I 1/16 l/4 1 18 8 to 14 3132 15 to27 1 /8 28 to 52 I 3/16 I For Sta...

Ngày tải lên: 11/08/2014, 08:22

... hole in spring end. ILLUSTRATED SOURCEBOOK of MECHANICAL COMPONENTS SECTION 15 12 Ways to put Balls to Work 15-2 15-4 Rubber Balls Find Many Jobs 15-6 Multiple Use of Balls in Milk ... 8. ) From charts Number of impacts per revolution for a D/d ratio of 5.71 is 7 .8, Fig 2. Impacts are the number of balls that pass one point on the nut in one revo-...

Ngày tải lên: 11/08/2014, 08:22

... The follower of this type of flat-face cam moves radially, Fig 5. The general equation of the family of lines forming the envelope is where y=m+b m = cos 8 L = lift of follower x ... formed. Sheetmetal screws hold panel. ILLUSTRATED SOURCEBOOK of MECHANICAL COMPONENTS SECTION 20 Fastening Studs and Pins to Plates 20-2 20-4 20-6 20 -8 20- 10 2...

Ngày tải lên: 11/08/2014, 08:22