Illustrated Sourcebook of Mechanical Components Part 6 pps
Illustrated Sourcebook of Mechanical Components Part 6 pps
...
>ength*:
3/32
913
2
318
3/ 16
R
I
2E
I
(maximum)
1 /64
1
0.005
I
0.002
1 164
0005
0002
1/32
0
0 06 0 003
3 /64
1
0 007
!
0
004
i 1
1/32
1
0.0 06
1
0.003
Note:
All
dimensions ...
ONE-PARALLEL
SERIES
26
1.87
1.10
1.7
0.034
0.085
0.4
0.884
2.21
60 0
305,000
THREE-PARALLEL
SERIES
48
1.87
1.10
1.7
0.055
0.0 46
1.2
0.884
2.21
60...
Illustrated Sourcebook of Mechanical Components Part 9 pps
... formed. Sheetmetal screws
hold
panel.
ILLUSTRATED SOURCEBOOK
of
MECHANICAL COMPONENTS
SECTION
20
Fastening Studs and Pins
to
Plates
20-2
20-4
20 -6
20-8
20-
10
20-12
Fastening Precision ... certain
curve, and if at each point
of
this curve at least one
member
of
the family
is
tangent, the curve is either
a
part or the whole of the envelope
of
the fa...
Illustrated Sourcebook of Mechanical Components Part 12 pps
...
of
Linkage
by
Use
of
Center Point
Curve Consisting
of
Two
Straight Lines
8
Tliis is another csample of the use of the simplified shape of the center-
point curve for the design of ...
column. For example,
Ratio of amplitude
of
2nd to 1st:
(a,)
=
0.0793 26
=
7.9%
Ratio
of
amplitude of 3rd
to
1st:
(d,)
=
0.012913
=
1.3%
The significance of th...
Illustrated Sourcebook of Mechanical Components Part 1 pptx
...
64 .3050
65 .3722
64 .0000
66 .0000
66 .4392
65 . 066 6 67 . 066 6
67 .5 062
66 .1333
68 .1333 68 .5733
67 .2000
69 .2000 69 .64 04
68 . 266 6 70. 266 6
70.7073
I
64
MEASUREMENT
\UMBER
OF
PITCH DIAMETER ...
45
46
47
48
49
42 .66 66
43.7333
44.8000
45. 866 6
46. 9333
49. 066 6
50.1333
51.2000
52. 266 6
48.oooo
44 .66 66
45.7333
46. 8000
47. 866 6...
Illustrated Sourcebook of Mechanical Components Part 2 potx
... 2. 169 7 in.
sprocket,
cos
0
=
O=
-
-
O=
cos
9
=
- -
9=
1 .66 67 in.
r2
+
C2
-
R,2
2rC
0.5032
+
2. 169 P
-
1.71 46& apos;
2
x
0.503
x
2. 169 7
0.92 567
22.2302"
1.71 462 ...
THE
SUCCESS
of the overhead trolley conveyor
is
largely the result of the development and
use
of drop-
forged, rivetless, Keystone chain. The dimensions of
several size...
Illustrated Sourcebook of Mechanical Components Part 3 docx
...
more projecting pins, the
3um
of the radii
of
the pins
being equal to the eccentricity of offset of the shafts.
The lines of criiter between each pair of pins remain
parallel as the coupling ...
Aluminum
multiply
uolues
of
N,
byLOO 26
,
For
Mognosium
multipb
vofues
of
Nc
by
0.9879
\
.
4- 26
m
:D,
/
8HC3
3.
Design
chart for different values
of...
Illustrated Sourcebook of Mechanical Components Part 4 pptx
... and
Eq
(2),
accurate values
I
of
torque can
be
easily determined.
ILLUSTRATED
SOURCEBOOK
of
MECHANICAL COMPONENTS
SECTION
9
Various Methods of Locking Threaded Members
Locking-Type ... Adjustable Parts
How Spring Clamps Hold Workpieces
9-2
9-4
9-8
9-10
9-12
9-14
9- 16
9-18
9-20
9-22
9-24
9- 26
9-30
9-34
9- 36
9-38
9-40
9-42
9-44
9- 46
9-48
9...
Illustrated Sourcebook of Mechanical Components Part 5 pdf
... sides of sheet.
FIG. 11-For attachment of recessed,
solid metallic or non-metallic parts in
thick-sectioned cylindrical parts.
FIG.
12-For
closing the end(s)
of
cylin-
drical parts. ... edge
of
the stationary part. This method is effective, but
removal
of
the clamped part may be difficult if it is heavy
or
unbalanced.
FIG.
3-The movable part is held against one s...
Illustrated Sourcebook of Mechanical Components Part 7 potx
...
shoft
*
*I
*1
3,
,
>>
",
ST-BEARjNG
TAKES
LIGHT
LOADS.
'
I
ILLUSTRATED SOURCEBOOK
of
MECHANICAL
COMPONENTS
SECTION
16
12 Ways to Put Springs
to
Work
16- 2 ... Mechanisms 16- 26
Flat Springs Find More Work 16- 28
12 Detents for Mechanical Movement 16- 30
17 Ways of Testing Springs
16- 32
Overriding Spring Mechanisms for low-Torque Dri...
Illustrated Sourcebook of Mechanical Components Part 8 doc
...
and knowing that 6, ,,,,=0.74 mm
gives a maximum-load value
of
F,,,,=300 kg (66 3 lb).
Thus the spring may be loaded be-
tween
155
and 300 kg for an in-
definite number
of
times. Moreover, ... space.
ILLUSTRATED SOURCE
BOOK
of
MECHANICAL COMPONENTS
SECTION
18
CAMS
Generating Cam Curves 18-2
Balance Grooved Cams 18-9
Computer and
N/C
Simplifies Cam Design 18-15...