Handbook Properties and Selection Nonferrous Alloys and Spl Purpose Mtls (1992) WW Part 11 docx

... Ni-Ti alloys and the copper- base alloys. Properties of the two systems are quite different. The Ni-Ti alloys have greater shape memory strain (up to 8% versus 4 to 5% for the copper-base alloys) , ... these alloys has yet to be determined, but the effort has opened up new classes of alloys for exploration as shape memory alloys. These new classes included β-Ti alloys and...

Ngày tải lên: 11/08/2014, 07:23

... Forgings; aircraft and diesel engine pistons; aircraft engine cylinder heads; jet engine impellers and compressor rings Mechanical Properties Tensile properties. See Tables 30 and 31. Table 30 ... Typical uses. Sheet and plate in structural components for aerospace application and military equipment Mechanical Properties Tube (hydraulic) 4086 . . . . . . Rivet wire and...

Ngày tải lên: 11/08/2014, 07:23

... heading and upsetting, hot forging and pressing, piercing and punching, roll threading and knurling, shearing, spinning, squeezing, and stamping Weldability. Joining by soldering, brazing, and ... connectors, clips, and other current-carrying parts requiring strength and exceptional softening resistance. Applications requiring excellent hot and cold workability, high...

Ngày tải lên: 11/08/2014, 07:23

... multilined spectrum of incandescent scandium vapor. Turning of scandium can be ignited and will burn white hot. Finely divided scandium should not be handled in air. Ingots of pure scandium can be stored ... Pearce, and R.O.A. Hall, J. Phys. Chem. Solids, Vol 11, 1959, p 177-181 572. H.A. Eick and R.N.R. Mulford, J. Chem. Phys., Vol 41, 1964, p 1475-1478 573. U. Benedict, Hand...

Ngày tải lên: 11/08/2014, 07:23

... melting, molten metal handling, dross handling and disposition, and welding of alloys. Standard define the maximum beryllium in welding rod and weld base metal as 0.008 and 0.010%, respectively. ... agents can be used for bonding the sand. The agent most often used is a mixture of clay and water. (Sand bonded with clay and water is called green sand). Sand bonded with oils or...

Ngày tải lên: 11/08/2014, 07:23

... brazed, and many coppers and copper alloys can be welded by various gas, arc, and resistance methods. For decorative parts, standard alloys having specific colors are readily available. Copper alloys ... power tools, appliances, and structural parts. Due to their mechanical and physical properties, aluminum P/M alloys provide engineers with flexibility in material sele...

Ngày tải lên: 11/08/2014, 07:23

... permanent mold, and sand castings for hardware fittings; valves and valve trim; statuary, and ornamental castings Mechanical Properties Tensile properties. Typical data for sand-cast test bars: ... continuous, and sand castings for valves, pump bodies, flanges, and elbows for applications requiring resistance to seawater corrosion Mechanical Properties Tensile proper...

Ngày tải lên: 11/08/2014, 07:23

... yield strength. 130 MPa (19 ksi) Tensile and compressive properties versus temperature. See Table 11 and Fig. 5. Table 11 Typical tensile and compressive properties of HM21A at elevated temperatures ... 100 114 66 93 200 119 69 150 300 123 71 200 400 128 74 260 500 132 76 O temper 18 65 107 62 38 100 107 62 93 200 110 64 150 300 114 66 200 400 119 69 260 500...

Ngày tải lên: 11/08/2014, 07:23

... Corrosion, Volume 13 of ASM Handbook, formerly 9th Edition Metals Handbook. Energy Production and Storage. Titanium plate-type heat exchangers, condensers, and piping and tubing are common in ... tungsten-base alloys usually divide them into four classes based on composition (Table 23) and three types based on tensile properties (Table 24). Tables 25 and 26 give typical mec...

Ngày tải lên: 11/08/2014, 07:23

... compositions, properties, and applications of dental alloys can be found in Ref 9 and 10, and in the article "Tarnish and Corrosion of Dental Alloys& quot; in Corrosion, Volume 13 of ASM Handbook, ... strong and is used for spring-type electrical contacts. Mechanical Properties Tensile properties. See Fig. 2 and 3. Fig. 2 Tensile properties and electrical c...

Ngày tải lên: 11/08/2014, 07:23