Volume 08 - Mechanical Testing and Evaluation Part 14 pdf

... Committee on Mechanical Testing of Welds, Mechanical Testing of Welds, Part 1: Summary of Tension Testing of Welds, Weld. J., Jan 1981, p 33–37 9. “Standard Methods for Mechanical Testing of ... ANSI/AWS B4. 0-9 8, American National Standards Institute/American Welding Society, Miami, 1998 10. B4 Committee on Mechanical Testing of Welds, Mechanical Testing of Wel...

Ngày tải lên: 10/08/2014, 12:22

... Impact Test, Impact Testing of Metals, STP 466, ASTM, 1970, p 148 –164 28. D.R. Ireland, W.L. Server, and R.A. Wullaert, “Procedures for Testing and Data Analysis,” ETI Report TR-7 5-4 3, Effects Technology, ... Marandet and G. Sanz, Evaluation of the Toughness of Thick Medium-Strength Steels by Using Linear Elastic Fracture Mechanics and Correlations Between K Ic and...

Ngày tải lên: 10/08/2014, 12:22

... 55 8 159 23 0.17 193 28 - 0.106 1.8 -0 .69 2 014 T6 temper 448 65 703 102 0.073 786 114 - 0 .081 0.85 -0 .86 2024 T351 temper 448 65 786 114 0.09 1 014 147 -0 .11 0.21 -0 .52 2024 T4 temper ... 0.065 1103 160 - 0.124 0.22 -0 .59 2219 T851 temper 331 48 793 115 0 .14 834 121 -0 .11 1.33 - Fig. 11 Three-point and four-point bending specimens,...

Ngày tải lên: 10/08/2014, 12:22

... Mechanical Testing and Evaluation was published in 2000 as Volume 8 of the ASM Handbook. The Volume was prepared under the direction of the ASM Handbook Committee. Volume Coordinator The Volume ... new articles and an all-new Volume 8 of the ASM Handbook series. As before, the key purpose of this Handbook volume is to explain test set-up, common testing problems an...

Ngày tải lên: 10/08/2014, 12:22

... 1100-O 180 26 0.20 2024-T4 690 100 0.16 5052-O 210 30 0.13 6061-O 205 30 0.20 6061-T6 410 59 0.05 7075-O 400 58 0.17 Brass 6 0-3 9-1 Pb, annealed 800 116 0.33 7 0-3 0, ... right-hand thread, and the other has a left-hand thread. For alignment and lateral stability, the screws are supported in elongations up to 2000% at strain rates on the order of...

Ngày tải lên: 10/08/2014, 12:22

... 33 (Ref 14 ). This figure illustrates true yield stress at various strains for a low-carbon steel at room temperature. Between strain rates of 10 -6 s -1 and 10 -3 s -1 (a thousandfold ... distinct parts: • Test-piece preparation, geometry, and material condition • Test setup and equipment • Test 1. D. Lewis, Tensile Testing of Ceramics and Ceramic-Matrix...

Ngày tải lên: 10/08/2014, 12:22

... max” and “good min” lines in Fig. 15 encompass the range of “good” data shown in Fig. 14. Again, several HV-versus-force trends are observed: labs E, H, and J follow trend 1, and labs F and ... Testing George F. Vander Voort, Buehler Ltd. Vickers Hardness Test In 1925, Smith and Sandland of the United Kingdom developed an indentation test that employs a square-based pyram...

Ngày tải lên: 10/08/2014, 12:22

... contained in Ref 2 and 6. Mechanical testing and indentation testing of thin films are also covered in the article Evaluation of Mechanical Properties of Thin Films” in the ASM Handbook, Volume 5, ... Hardness, and Scleroscope Hardness),” E 14 0-9 7e1, Annual Book of ASTM Standards, ASTM 6. “Standard Test Method for Hardness Testing of Cemented Carbides,” B 29 4-9 2...

Ngày tải lên: 10/08/2014, 12:22

... contact (ball-on-flat, ball-on-ball, crossed cylinders) Line contact (roller-on-flat; roller-on-roller, axes parallel) Flat-on-flat Conforming (sleeve or journal bearing) Velocity and load ... Block-on-Ring Test Crossed cylinders G 83 Standard Test Method for Wear Testing with a Crossed Cylinder Apparatus Pin-on-disk G 99 Standard Test Method for Wear Testing with a Pin-on-...

Ngày tải lên: 10/08/2014, 12:22

... plate-on-plate, rod-on-plate, plate-on-rod, or rod-on-rod experiments. Two types of plate-on-plate impact tests have been developed: wave propagation experiments and thin-layer high-strain- rate ... high-temperature, low-velocity impact tests. Dimensions in inches. Source: Ref 44 84. G.T. Gray III and A.D. Rollett, The High-Strain-Rate and Spallation Response on Tantalum, TA-10W and...

Ngày tải lên: 10/08/2014, 12:22