Volume 08 - Mechanical Testing and Evaluation Part 13 pdf

... 51.2 957 138 .8 0.16 772 112.0 - 0 .08 0.34 - 0.52 SAE950X As-received, 409 59.3 939 136 .2 0 .13 824 119.5 -0 .42 - Introduction to Mechanical Testing of Components Introduction TESTING ... properties (c) A136 As-received 330 47.9 1026 148.8 0.18 799 115.9 - 0.09 0.22 - 0.46 A136 150 HB 337 48.9 1151 167.0 0.2 846 122.7 - 0 .08 0.2...

Ngày tải lên: 10/08/2014, 12:22

... July 1971 13. B. Marandet and G. Sanz, Evaluation of the Toughness of Thick Medium-Strength Steels by Using Linear Elastic Fracture Mechanics and Correlations Between K Ic and Charpy V-Notch, ... data from various steels including 2.25Cr-1Mo, 1.25Cr-0.50Mo, 1Cr and 0.50Mo chemical pressure vessel steels, and ASTM A 508 C1.1, A 508 C1.2, A 508 C1.3 and A 533 Gr.B C1.1 n...

Ngày tải lên: 10/08/2014, 12:22

... Committee on Mechanical Testing of Welds, Mechanical Testing of Welds, Part 1: Summary of Tension Testing of Welds, Weld. J., Jan 1981, p 33–37 9. “Standard Methods for Mechanical Testing of ... ANSI/AWS B4. 0-9 8, American National Standards Institute/American Welding Society, Miami, 1998 10. B4 Committee on Mechanical Testing of Welds, Mechanical Testing of Wel...

Ngày tải lên: 10/08/2014, 12:22

... Mechanical Testing and Evaluation was published in 2000 as Volume 8 of the ASM Handbook. The Volume was prepared under the direction of the ASM Handbook Committee. Volume Coordinator The Volume ... new articles and an all-new Volume 8 of the ASM Handbook series. As before, the key purpose of this Handbook volume is to explain test set-up, common testing problems an...

Ngày tải lên: 10/08/2014, 12:22

... 1100-O 180 26 0.20 2024-T4 690 100 0.16 5052-O 210 30 0 .13 6061-O 205 30 0.20 6061-T6 410 59 0.05 7075-O 400 58 0.17 Brass 6 0-3 9-1 Pb, annealed 800 116 0.33 7 0-3 0, ... right-hand thread, and the other has a left-hand thread. For alignment and lateral stability, the screws are supported in elongations up to 2000% at strain rates on the order of...

Ngày tải lên: 10/08/2014, 12:22

... 111, ASTM 7. Making, Shaping, and Treating of Steel, 10th ed., U.S. Steel, 1985, Fig. 5 0-1 2 and 5 0-1 3 8. “Standard Test Methods and Definitions for Mechanical Testing of Steel Products,” A 370, ... distinct parts: • Test-piece preparation, geometry, and material condition • Test setup and equipment • Test 1. D. Lewis, Tensile Testing of Ceramics and Ceramic-Mat...

Ngày tải lên: 10/08/2014, 12:22

... Testing George F. Vander Voort, Buehler Ltd. Vickers Hardness Test In 1925, Smith and Sandland of the United Kingdom developed an indentation test that employs a square-based pyramidal-shaped ... max” and “good min” lines in Fig. 15 encompass the range of “good” data shown in Fig. 14. Again, several HV-versus-force trends are observed: labs E, H, and J follow trend 1, and la...

Ngày tải lên: 10/08/2014, 12:22

... contained in Ref 2 and 6. Mechanical testing and indentation testing of thin films are also covered in the article Evaluation of Mechanical Properties of Thin Films” in the ASM Handbook, Volume 5, ... diam ball, HBS (e) 130 127.0 138 .7 133 .8 … 85.0 … 67.0 99.0 … 69.5 49.0 … 119.0 128 125.2 136 .8 132 .1 83.0 84.5 … 66.0 98.0 87.0 68.5 48.0 … 117.5 126 123.6 134...

Ngày tải lên: 10/08/2014, 12:22

... contact (ball-on-flat, ball-on-ball, crossed cylinders) Line contact (roller-on-flat; roller-on-roller, axes parallel) Flat-on-flat Conforming (sleeve or journal bearing) Velocity and load ... is represented in pin-on-disk, crossed cylinders and four-ball tests, while flat-on-flat is shown in ring-on-ring, fretting bridge, and flat-on-flat configurations. observed over many ord...

Ngày tải lên: 10/08/2014, 12:22

... plate-on-plate, rod-on-plate, plate-on-rod, or rod-on-rod experiments. Two types of plate-on-plate impact tests have been developed: wave propagation experiments and thin-layer high-strain- rate ... high-temperature, low-velocity impact tests. Dimensions in inches. Source: Ref 44 84. G.T. Gray III and A.D. Rollett, The High-Strain-Rate and Spallation Response on Tantalum, TA-10W and...

Ngày tải lên: 10/08/2014, 12:22