Volume 05 - Surface Engineering Part 1 pot
Volume 05 - Surface Engineering Part 1 pot
... (Member 19 3 7 -1 942) • L.B. Case (19 3 1- 1 933) (Member 19 2 7 -1 933) • T.D. Cooper (19 8 4 -1 986) (Member 19 8 1- 1 986) • E.O. Dixon (19 5 2 -1 954) (Member 19 4 7 -1 955) • R.L. Dowdell (19 3 8 -1 939) (Member 19 3 5 -1 939) ... protection 19 10 .13 3 Alkaline mist exposure Goggles or face shield 19 10 .13 4 19 10 .10 00 Alkaline cleaning Skin contact Impervi...
Ngày tải lên: 10/08/2014, 12:22
Volume 05 - Surface Engineering Part 6 potx
... (CN); 17 .5 to 43.7 g/L (2.33 to 5.82 oz/gal) NaCN; 75.2 g/L (10 oz/gal) NaOH; 2.0-to -1 to 2.75-to- 1 ratios of NaCN to zinc. Temperature: 30 °C (86 °F). (b) Effect of zinc metal content. 60 .1, ... content. 60 .1, 75.2, and 90.2 g/L (8, 10 , and 12 oz/gal) Zn (CN); 43.7, 54.6, and 65.5 g/L (5.82, 7.27, and 8.72 oz/gal) NaCN; 75.2 g/L (10 oz/gal) NaOH; 2.75-to- 1 ratio of NaCN to...
Ngày tải lên: 10/08/2014, 12:22
Volume 05 - Surface Engineering Part 9 potx
... Dryoff. (10 ) Curing oven. (11 ) Deionized quench for cooling. (12 ) Offload area. (13 ) Source for direct current. (14 ) To anodes in paint bath. (15 ) To work on conveyor. (16 ) Particl e filter. (17 ) ... x ftgalspreading x = Table 10 Theoretical spreading rate for coatings 13 μm (0.5 mil) 25 μm (1. 0 mil) 38 μm (1. 5 mils) 51 μm (2.0 mils) 64 μm (2.5 mils) 76 μm (3.0 mils )Volume s...
Ngày tải lên: 10/08/2014, 12:22
Volume 05 - Surface Engineering Part 12 pot
... class="bi x 11 yd9 w5 h27" alt=""
Ngày tải lên: 10/08/2014, 12:22
Volume 05 - Surface Engineering Part 2 ppsx
... Time, s 1 0 -1 5 sulfuric plus 0-4 hydrofluoric 5 0-6 5 12 0 -1 50 2 0-6 0 Ferritic 5 -1 0 nitric plus 0. 2 -1 hydrofluoric 5 0-6 5 12 0 -1 50 2 0-6 0 Austenitic 1 0 -1 5 sulfuric plus 0-4 hydrofluoric ... Vol 17 (No. 10 ), 19 65, p 11 2 1- 1 12 5 21. C.W. Tuck, The Effect of Scale Microstructure on the Pickling of Hot-Rolled Steel Strip...
Ngày tải lên: 10/08/2014, 12:22
Volume 05 - Surface Engineering Part 4 docx
... Temperature, °C (°F) . . . 7 1- 8 2 (16 0 -1 80) 82 (18 0) Time, min . . . 2 1 2 Drying Temperature, °C (°F) 8 2- 10 5 (18 0-2 20) 8 2- 10 5 (18 0-2 20) 8 2- 10 5 (18 0-2 20) Time, min 1- 3 5 1- 3 Acid Baths The ... 3 0-4 1 4. 0-5 .5 20 2.7 1 5-2 8 2. 0-3 .7 Sodium hydroxide 79 10 .5 6 8- 10 5 9. 0 -1 4.0 75 10 .0 6 0-9 0 8. 0...
Ngày tải lên: 10/08/2014, 12:22
Volume 05 - Surface Engineering Part 5 ppt
... 10 .5 11 3 15 .0 11 .0 11 9 15 .8 11 .5 12 4 16 .5 12 .0 13 0 17 .3 12 .5 13 7 18 .2 13 .0 14 4 19 .1 13 .5 14 9 19 .8 14 .0 15 3 20.4 14 .5 15 9 21. 2 15 .0 16 5 22.0 15 .5 17 2 ... conditions pH 8. 5 -1 0 8 -1 0 4-6 4. 3-4 .6 4. 5-5 .5 4. 5-5 .5 Temperature, °C (°F) 9 0-9 5 (19 5- 205) 9 0-9 5 (19 5- 205) 8...
Ngày tải lên: 10/08/2014, 12:22
Volume 05 - Surface Engineering Part 7 docx
... oz/gal g/L oz/gal Operating conditions Bath 1 Bath 2
Ngày tải lên: 10/08/2014, 12:22
Volume 05 - Surface Engineering Part 8 pptx
... 5Paint (film) characteristics 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 General Surface Conditions After Galvanizing. Table 8 Guide for visual inspection of galvanized surfaces Condition Causes Grounds ... compressive strength (a)(c) Hardness, HB (d) Composition, % At 19 °C (66 °F) At 10 0 °C ( 212 °F) At 19 °C (66 °F) At 10 0 °C ( 212 °F) Melting point Complete liquefaction...
Ngày tải lên: 10/08/2014, 12:22