The Welding of Aluminum & Its Alloys Part 12 pot
The Welding of Aluminum & Its Alloys Part 12 pot
... sides of the component, the source on one side, the film on the other. • There are problems in detecting planar defects and fine cracks if these are normal to the beam. • There is a limitation on the ... par- ticular topic, others are included for those who wish to gain a more general under- standing of the principles of metallurgy, the uses of aluminium and the weldi...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 2 pps
... and the grain size of the deposit.These in their turn depend on the parent and filler metal compositions, the amount of dilution, the quality of the welding process and the welder and, lastly, the ... been strengthened by either cold working or precipitation hardening. One aspect of this is the width of the HAZ, a function of the high thermal conductiv- ity...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 3 docx
... identify the condition of the alloy, in other words the amount of cold work the alloy has undergone or its heat treatment con- dition. There are a number of schemes available for identification of the alloy ... necessary to weld the lower copper-containing alloys then 4047 is the best choice as a filler metal. 50 The welding of aluminium and its alloys treatm...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 4 pdf
... will depend on the size of the equipment to be used, in particular the size of the torch. Welding aluminium with the gas shielded processes 70 The welding of aluminium and its alloys Visible ... design of edge preparation. Joint design is determined by the strength requirements, the alloy, the thickness of the material, the type and location of the...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 6 pps
... rod can also shield the material ahead of the weld pool from the cleaning action of the arc and this may also lead to oxide entrapment. 110 The welding of aluminium and its alloys 80° 10 to 20° ... flexible. Overheating of the torch can melt the brazed joints within the torch or the plastic tube that sheaths the power cable and it is important that 106 The...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 7 docx
... transfer. If the tip is too close to the end of the gas shroud there is an increased risk of spatter damaging the tip. If the tip protrudes from the shroud then there is a risk of the tip touching ... most of these modern units a crater filling facility is built in, which automatically fades out the current when the trigger on the gun is released. 122 The weldin...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 8 ppt
... range of materials (Fig. 8.2). The laser welding of aluminium and its alloys has, however, presented problems to the welding engineer. Poor coupling of the beam with the parent metal, high thermal ... of the wire position and the wire feed speed, as a balance must be achieved between the volume of metal being fed into the pool, the volume of the mould a...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 9 pptx
... present. 9.4 Spot welding 9.4.1 Spot welding principles and parameters Spot welding is by far the most widely used variant of the resistance welding process. The basic principles of the technique ... melting, adhesion of the electrodes, pits, cracks, asymmetry of the weld spot and 174 The welding of aluminium and its alloys incompatible alloys that cann...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 10 doc
... a WPS for the welding of aluminium or its alloys shall be approved. It gives the limits of validity of the WPS within the range of variables and includes an example of a WPAR and the accom- panying ... Tests for the Arc Welding of Steel. • Part 4 Welding Procedure Tests for the Arc Welding of Aluminium and its Alloys. • Part 5 Welding Approva...
Ngày tải lên: 10/08/2014, 12:21