The Welding of Aluminum & Its Alloys Part 9 pptx
The Welding of Aluminum & Its Alloys Part 9 pptx
... determines the peripheral speed, the pressure applied during the welding process and the duration of the weld cycle. The metal extruded from the joint forms a flash on the outside of the weld and ... present. 9. 4 Spot welding 9. 4.1 Spot welding principles and parameters Spot welding is by far the most widely used variant of the resistance welding proce...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 2 pps
... and the grain size of the deposit.These in their turn depend on the parent and filler metal compositions, the amount of dilution, the quality of the welding process and the welder and, lastly, the ... been strengthened by either cold working or precipitation hardening. One aspect of this is the width of the HAZ, a function of the high thermal conductiv- ity...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 3 docx
... identify the condition of the alloy, in other words the amount of cold work the alloy has undergone or its heat treatment con- dition. There are a number of schemes available for identification of the alloy ... necessary to weld the lower copper-containing alloys then 4047 is the best choice as a filler metal. 50 The welding of aluminium and its alloys treatm...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 4 pdf
... will depend on the size of the equipment to be used, in particular the size of the torch. Welding aluminium with the gas shielded processes 70 The welding of aluminium and its alloys Visible ... design of edge preparation. Joint design is determined by the strength requirements, the alloy, the thickness of the material, the type and location of the...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 6 pps
... rod can also shield the material ahead of the weld pool from the cleaning action of the arc and this may also lead to oxide entrapment. 110 The welding of aluminium and its alloys 80° 10 to 20° ... flexible. Overheating of the torch can melt the brazed joints within the torch or the plastic tube that sheaths the power cable and it is important that 106 The...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 7 docx
... end the welding sequence. This is generally achieved by means of a trigger on the handle of the torch. Operating the trigger initiates the shielding gas flow and the welding current when the ... this is at the torch, not at the outlet of the cylinder regulator! 7.3.2 Welding filler wire The wire acts as both the filler metal and the anode in the welding...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 8 ppt
... range of materials (Fig. 8.2). The laser welding of aluminium and its alloys has, however, presented problems to the welding engineer. Poor coupling of the beam with the parent metal, high thermal ... for the avoidance of lack of penetration or porosity. Other welding processes 153 8.4 Laser weld of dissimilar thickness of automotive panelling. Courtesy of...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 10 doc
... a WPS for the welding of aluminium or its alloys shall be approved. It gives the limits of validity of the WPS within the range of variables and includes an example of a WPAR and the accom- panying ... Tests for the Arc Welding of Steel. • Part 4 Welding Procedure Tests for the Arc Welding of Aluminium and its Alloys. • Part 5 Welding Approva...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 11 pps
... affected by the source to film distance – the greater this is the sharper the image; the size of the radiation source – the smaller the source the sharper the image; the beam energy – the higher the ... completes one of the above tests then there is no limit to their range of approval. This is provided that they continue to work with the same type of wel...
Ngày tải lên: 10/08/2014, 12:21