The Welding of Aluminum & Its Alloys Part 6 pps

The Welding of Aluminum & Its Alloys Part 6 pps

The Welding of Aluminum & Its Alloys Part 6 pps

... rod can also shield the material ahead of the weld pool from the cleaning action of the arc and this may also lead to oxide entrapment. 110 The welding of aluminium and its alloys 80° 10 to 20° ... mechanisation is simplified if the weld is 114 The welding of aluminium and its alloys results in overheating and melting of the electrode. Manual TIG weldin...
Ngày tải lên : 10/08/2014, 12:21
  • 20
  • 354
  • 0
The Welding of Aluminum & Its Alloys Part 2 pps

The Welding of Aluminum & Its Alloys Part 2 pps

... and the grain size of the deposit.These in their turn depend on the parent and filler metal compositions, the amount of dilution, the quality of the welding process and the welder and, lastly, the ... been strengthened by either cold working or precipitation hardening. One aspect of this is the width of the HAZ, a function of the high thermal conductiv- ity...
Ngày tải lên : 10/08/2014, 12:21
  • 20
  • 339
  • 0
The Welding of Aluminum & Its Alloys Part 11 pps

The Welding of Aluminum & Its Alloys Part 11 pps

... affected by the source to film distance – the greater this is the sharper the image; the size of the radiation source – the smaller the source the sharper the image; the beam energy – the higher the ... completes one of the above tests then there is no limit to their range of approval. This is provided that they continue to work with the same type of wel...
Ngày tải lên : 10/08/2014, 12:21
  • 20
  • 338
  • 0
The Welding of Aluminum & Its Alloys Part 13 ppsx

The Welding of Aluminum & Its Alloys Part 13 ppsx

... sources 167 – 169 seam welding 175–1 76 spot welding 171–175 surface condition 169 –171 2 36 Index solidification cracking see hot cracking solid solution strengthening see alloying storage of parent ... 22 effect of cleanliness 21 composition 20 hose type 20 process 20 gas dew point 20 ISO classification 200 precipitation (age) hardening 16 17 resistance welding flash butt welding...
Ngày tải lên : 10/08/2014, 12:21
  • 2
  • 263
  • 0
The Welding of Aluminum & Its Alloys Part 3 docx

The Welding of Aluminum & Its Alloys Part 3 docx

... 53 56 53 56 5554 53 56 53 56 5083 5183 53 56 5183 53 56 53 56 50 86 53 56 53 56 5183 53 56 53 56 5454 53 56 5554 5554 53 56 5554 54 56 55 56 53 56 55 56 53 56 55 56 6 061 53 56 53 56 4043 4043 565 4 60 63 53 56 53 56 4043 ... 5083 60 63 7019 1200 5251 60 82 7020 5454 7039 8090 55 56 55 56 7039 55 56 55 56 53 56 55 56 55 56 7019 53 56 53 56 53 56 53 56 702...
Ngày tải lên : 10/08/2014, 12:21
  • 20
  • 338
  • 0
The Welding of Aluminum & Its Alloys Part 4 pdf

The Welding of Aluminum & Its Alloys Part 4 pdf

... will depend on the size of the equipment to be used, in particular the size of the torch. Welding aluminium with the gas shielded processes 70 The welding of aluminium and its alloys Visible ... design of edge preparation. Joint design is determined by the strength requirements, the alloy, the thickness of the material, the type and location of the...
Ngày tải lên : 10/08/2014, 12:21
  • 20
  • 420
  • 0
The Welding of Aluminum & Its Alloys Part 7 docx

The Welding of Aluminum & Its Alloys Part 7 docx

... most of these modern units a crater filling facility is built in, which automatically fades out the current when the trigger on the gun is released. 122 The welding of aluminium and its alloys 7 .6 ... this is at the torch, not at the outlet of the cylinder regulator! 7.3.2 Welding filler wire The wire acts as both the filler metal and the anode in the weldi...
Ngày tải lên : 10/08/2014, 12:21
  • 20
  • 338
  • 0
The Welding of Aluminum & Its Alloys Part 8 ppt

The Welding of Aluminum & Its Alloys Part 8 ppt

... range of materials (Fig. 8.2). The laser welding of aluminium and its alloys has, however, presented problems to the welding engineer. Poor coupling of the beam with the parent metal, high thermal ... strength the gap between the plates should be as small as possible. 1 46 The welding of aluminium and its alloys attainable .The main welding parameter is...
Ngày tải lên : 10/08/2014, 12:21
  • 20
  • 357
  • 0
The Welding of Aluminum & Its Alloys Part 9 pptx

The Welding of Aluminum & Its Alloys Part 9 pptx

... 4.0 3 .6 35 8 2.0 22 4.0 4.0 3.8 41 8 2.3 22 6. 0 6. 0 4.25 46 10 2.5 22 6. 0 6. 0 4.7 56 12 3.2 22 6. 0 6. 0 5.8 76 12 which is generated a high-energy density beam of electrons of the order of 0.25–2.5mm ... age-hardened alloys, is close to 1, implying that there is a limited loss of strength. The softening factors of 0.83 for the 60 82-T6 alloy can be compared w...
Ngày tải lên : 10/08/2014, 12:21
  • 20
  • 202
  • 0