The Welding of Aluminum & Its Alloys Part 4 pdf
The Welding of Aluminum & Its Alloys Part 4 pdf
... will depend on the size of the equipment to be used, in particular the size of the torch. Welding aluminium with the gas shielded processes 70 The welding of aluminium and its alloys Visible ... design of edge preparation. Joint design is determined by the strength requirements, the alloy, the thickness of the material, the type and location of the...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 2 pps
... in the case of fusion welding above the melting point of the parent metals, and brought together to enable the components to coalesce. The heat of the welding operation is conducted into the ... metal(s). The proper- ties of this weld depend upon the composition, the quality and the grain size of the deposit.These in their turn depend on the parent and...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 3 docx
... 5356 5356 40 43 40 43 56 54 6063 5356 5356 40 43 40 43 6356 6082 40 43 40 43 40 43 40 43 40 43 7005 5556 5356 5356 5356 5356 7039 5556 5356 5356 5356 5356 particles can also become embedded in the packing ... 5556 3105 NS 40 43 5056 5356 40 43 40 43 2219 2319 2319 40 43 1050 40 43 2319 1080 1050 40 43 1200 1080 Material standards, designations and alloys 41 cavities that...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 6 pps
... Courtesy of TWI Ltd. 1 04 The welding of aluminium and its alloys RUNS FILLER mm SPEED mm/min 1 1 1 1 1 1 1 1.6–2 .4 2 .4 3.2 4. 8 4. 8 4. 8 4. 8 150 150 200 280 230 190 200 0 50 100 150 200 250 300 350 40 0 WELD ... 1.2 42 0 1 sq. butt nil 26 20 1 1.6 42 0 1.5 sq. butt nil 45 20 1 1.6 48 0 2 .4 sq. butt nil 80 17 1 2 .4 300 2 .4 fillet 130 14 1 2 .4 540 3.2 sq. b...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 7 docx
... end the welding sequence. This is generally achieved by means of a trigger on the handle of the torch. Operating the trigger initiates the shielding gas flow and the welding current when the ... this is at the torch, not at the outlet of the cylinder regulator! 7.3.2 Welding filler wire The wire acts as both the filler metal and the anode in the welding...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 8 ppt
... range of materials (Fig. 8.2). The laser welding of aluminium and its alloys has, however, presented problems to the welding engineer. Poor coupling of the beam with the parent metal, high thermal ... strength the gap between the plates should be as small as possible. 146 The welding of aluminium and its alloys attainable .The main welding parameter is...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 9 pptx
... melting, adhesion of the electrodes, pits, cracks, asymmetry of the weld spot and 1 74 The welding of aluminium and its alloys incompatible alloys that cannot be fusion welded together can be success- fully ... present. 9 .4 Spot welding 9 .4. 1 Spot welding principles and parameters Spot welding is by far the most widely used variant of the resistance weldi...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 10 doc
... Tests for the Arc Welding of Steel. • Part 4 Welding Procedure Tests for the Arc Welding of Aluminium and its Alloys. • Part 5 Welding Approval by Using Approved Welding Consumables for Arc Welding. • ... a WPS for the welding of aluminium or its alloys shall be approved. It gives the limits of validity of the WPS within the range of variab...
Ngày tải lên: 10/08/2014, 12:21
The Welding of Aluminum & Its Alloys Part 11 pps
... affected by the source to film distance – the greater this is the sharper the image; the size of the radiation source – the smaller the source the sharper the image; the beam energy – the higher the ... completes one of the above tests then there is no limit to their range of approval. This is provided that they continue to work with the same type of wel...
Ngày tải lên: 10/08/2014, 12:21